The hanger is supported using a rectangular pin. Determine the magnitude of the allowable suspended load P if the allowable bearing stress is (σb)allow=220 MPa, the allowable tensile stress is (σt)allow=150 MPa, and the allowable shear stress is τallow=130 MPa. Take t=6 mm, a=5 mm, and b=25 mm. draw free-body diagram

The hanger is supported using a rectangular pin. Determine the magnitude of the allowable suspended load P if the allowable bearing stress is (σb)allow=220 MPa, the allowable tensile stress is (σt)allow=150 MPa, and the allowable shear stress is τallow=130 MPa. Take t=6 mm, a=5 mm, and b=25 mm. draw free-body diagram

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer the following. If the allowable bearing stress for the material under the supports at A and B is σb = 820 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 650 lb/ft, a = 10 ft, and b = 5 ft.
The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is w = 75 mm and the bar thickness is 20 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax=
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
A 25 mm square-cross-section bar of length 300 mm carries an axial compressive load of 50 kN. Determine the stress set up in the bar and its change of length when the load is applied. For the bar material E = 200 MPa
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 10 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 8 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 100 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter d₁ of the top disk, and the largest diameter d₂ of the opening, and the largest diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (b) allow = 350 MPa and the allowable shear stress is Tallow=125 MPa. C B d₁ -| A 140 kN 20 mm 10 mm d3 d2
The bell-crank mechanism is in equilibrium for an applied load of F1 = 17 kN applied at A. Assume a = 290mm, b = 120mm, c = 80mm, and e = 35°. Pin B is in a double-shear connection and has a diameter of 33 mm. The bell crank has a thickness of 36 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F2 Support bracket A a Answers: Tpin B = MPa Ob = i MPa
5. The hanger is supported using the rectangular pin. Determine the magnitude of the allowable suspended load P if the allowable bearing stress is b,allow = 220 MPa, the allowable tensile stress is at,allow = 150 MPa, and the allowable shear stress is Tallow = 130 MPa. Take t = 6 mm, a = 5 mm and b = 25 mm. 75 mm 37.5 mm 20 mm 10 mm 37.5 mm
The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial distributed loading along its length of w 8 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 6 kN. Determine the normal stress in the rod at x = 1.5 m. Assume a = 0.7 m and b = 1.2 m. W ->P Q A B x a Answer: 0 = i MPa b
please help
The five-bolt connection must support an applied load of P = 2600 Ib. If the average shear stress in the bolts must be limited to 27 ksi, determine the minimum bolt diameter that may be used for this connection. Answer:dmin = in.