The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB is 9.9 KN. Determine the required tension 7 in cable AC such that th effect of the two cables is a downward force at point A. Determine the magnitude R of this downward force.

Q: A rectangular flume 3 meters wide and 1.8 meters deep, is carrying water to a depth of 1.2 meters…

A:

Q: 3. The box below contains the elevation of a point group (all in meters). Draw the 25-meter contour…

A: Finding out the contour line of 25 m .

Q: Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute…

A: Given data  2.7 KNm = 2700 Nm Find elastic curve equation, slope at point-B and deflection at…

Q: Define the Correction for N60 in Granular Soil ?

A: These are terms related to geotechnical engineering.

Q: In a one-lane one-way homogeneous traffic stream, the observed average headway is 3.0s. The flow…

A: Given data: In a one-lane one-way homogenous traffic stream, The observed average headway, Ht=3 s

Q: For the simply supported beam loaded as shown determine the slope and deflection at point(D) using…

A:

Q: 100 m³ of sludge holds a moisture content of 95%. If its moisture content changes to 90%, the volume…

A: given- volume V1=100 m3moisture P1=95%moisture P2=90%

Q: If the peak ordinate of a 4 h unit hydrograph of a basin is 270 m³/s, then the peak ordinate of a 8…

A: Given data,For 4 hour unit hydrograph,Peak ordinate =270 m3 /sTo fins the peak ordinate of  8  hour…

Q: F={26i?49j+55k}lb. 3 ft 4 ft B 4 ft 2 ft Determine the magnitude of the component of F acting along…

A: Given values: F = (26i - 49j + 55k) lb

Q: Q3) A leveling staff setup on point R of elevation (-8.79 m), is observed from point A ,where the…

A:

Q: 10-1. In a 5-day BOD test, the initial DO concentration was 7.8 mg/L and the final concentration was…

A:

Q: 2. Calculate the cut area of the drawing below both with the known shapes formula and with the…

A: This question is from survey engineering. Here we are given with a cross section of structure . This…

Q: express each common fraction as a decimal fraction. 8⁄25

A: Given data:- The given fraction is, 825

Q: In many applications, calibrated springs are commonly used to measure the magnitude of a force.…

A: Common force measuring tools The power produced by an engine, motor, or other rotating prime can be…

Q: Use 4 decimal places at all instances and box the final answers. Please write legibly Determine the…

A: Using equilibrium equation

Q: a. Determine the Reactions of the following structures.  b. Draw the Shear and Moment diagram…

A:

Q: 5.16. Determine the flow rate in the tube shown in Figure P5.16 if the manometer fluid is mercury…

A: Given ;

Q: Could you explain the calcutions in more detail like why you used does numbers in does ways

A:

Q: A circular primary clarifier processes 5005 cubic meters of municipal wastewater every day. The…

A: Given data: Average flow rate = 5005 m3/d The overflow rate = 35m3/m2d

Q: 5. A smooth plastic 10-m long garden hose with an inside diameter of 20 mm is used to drain a wading…

A:

Q: 2. Fine the stress in all the members and the reactions at A of the steel frame as shown in the…

A:

Q: The double-riveted butt joint as shown in the Figure connects two plates which are each 2.5 mm…

A: Given : Thickness of plate - 2.5 inches  dia of rivets = 3.0 mm failure strength of rivets in shear…

Q: PROBLEM 1: The beam shown below has a fixed support at A and a roller at B. El is constant. Use the…

A: Given data  EI = constant  Find 1. Support reaction using force method  2. Draw shear force and…

Q: An open channel is fitted with a rectangular and right angled V notch with coefficient of discharge…

A:

Q: 1870 g of wet soil compacted into a mold with a volume of 1000 cm3. The soil is put into the oven…

A: Given :

Q: o solid cylindrical rods support a load of P 22 kN, as shown. Rod (1) has a diameter of 12 mm and…

A: Given ;

Q: Q.2 The bar is made of an aluminium alloy having a stress-strain diagram that can be approximated by…

A: Solution: Given: Bar is made of an aluminium alloy ∈Max=0.05

Q: Problem 4. A. Draw the F.B.D. of the frame shown in Fig. B. Draw the F.B.D. of the figure shown in…

A: In the Given questions two different figures are shown we have to determine the FBD of the figures

Q: 4. If a soil has a submerged unit weight of 10.69 kN/m³, what will be its critical hydraulic…

A: Given data: A soil has a submerged unit weight, Y'=10.69 kNm3 Yw=9.81 kNm3 (standard value)

Q: Q1: A circular curve having coordinates given in the Table. The chainage/station of PC is 27+05m. R=…

A:

Q: 2.2m

A:

Q: 4. The engine hoist is used to support the 160-kg engine. Determine the force acting in the…

A:

Q: a)Determine the magnitude of the projected component of the force F = [ 60 i + 12 j - 35 k ] N along…

A: Given :

Q: A plate-bearing test using a 30-inch diameter rigid plate was made on a subgrade as well as on 10…

A: Given : Dia of rigid plate - 30 inches Thickness of gravel base = 10 inches  The unit load required…

Q: Convert 3.4 pounds to ounces.

A: Given data:- The given value in pounds, =3.4 pounds we know that, 1 Pounds=16 ounce

Q: Determine the horizontal and vertical reactions at the connections A and C. Assume that A, B, and C…

A: Given :

Q: State the procedure of Percussion drilling ? Define the importance of Percussion drilling ?

A: Steel casing tubes are used in the drilling technique known as percussion drilling to prevent the…

Q: The rating stamped on an oil burner nozzle tells the number of gallons of oilsprayed each hour. One…

A: Given:- The rating stamped on an oil burner nozzle tells the number of gallons of oil sprayed each…

Q: 4-38. A) For the concurrent force system shown, calculate the maximum load W that could be supported…

A:

Q: Q1 (a) Figure Q1 shows a large pressure vessel fabricated by welding together steel plates of 12 mm…

A: Given data The thickness of the steel plate (t) = 12 mm The stress acting normal to the weld = 80…

Q: A channel designed by Lacey's theory has a mean velocity of 1.1 m/s. The silt factor is 1.1. Then…

A:

Q: F2-28. Determine the component of projection of the force along the line OA. F = 650 N 8 13. 12 5 A…

A: Given :

Q: The cross section of a trapezoidal channel is shown. Side slopes are 2V:3H and the discharge is 30…

A:

Q: 1-Explain A case study of applications of RAMS and LCC in the Design Process?

A: The analysis RAMS (acronym of Reliability, Availability, Maintainability and Safety) is used to…

Q: Explain what is meant by moment or torque and give examples from everyday life.

A: The force that may induce an item to revolve along a direction is measured as torque. In classical…

Q: " Two concentric glass tubes immersed in water as shown in figure. The outer tube has diameter of (D…

A: Capillary Rise Capillary tubes are thin cylindrical tubes with extremely tiny diameters. The liquid…

Q: Situation: A beam has a width of 300 mm and an effective depth of 480 mm strength f'c-34 MPa. Steel…

A: Solution: Given: b = 300 mm d = 480 mm fc = 34 MPa fy = 415 MPa d'=70mm DL = 140 kN-m LL = 180 kN m…

Q: express each common fraction as a decimal fraction. 3⁄13

A: Given data:- The given common fraction is, 313

Q: Prob. 5.2-12. For the beam in Fig. P5.2-12. determine the following: (a) V₁ and M₁, the reactions at…

A:

Q: 50. In the figure below, the waterline section of a 1500 kN barge is as shown. Its center of gravity…

A: We have to calculate metacentric height against the rolling axis.

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.