The graph below shows the experimental stress - strain graphs for two materials, A and B. Identify which of the following statments is true. Stress (N mmn-²) 8 N mm-² 1.8 Nmm-2 Material A 1 x 10-5 A. The Young's modulus of elasticity of material B is 155 GPa B. The Young's modulus of elasticity of material B is 155 MPa O C. The Young's modulus of elasticity of material B is 15.5 MPa O D. The Young's modulus of elasticity of material B is 15.5 GPa Material B 5 x 10-5 Strain

The graph below shows the experimental stress - strain graphs for two materials, A and B. Identify which of the following statments is true. Stress (N mmn-²) 8 N mm-² 1.8 Nmm-2 Material A 1 x 10-5 A. The Young's modulus of elasticity of material B is 155 GPa B. The Young's modulus of elasticity of material B is 155 MPa O C. The Young's modulus of elasticity of material B is 15.5 MPa O D. The Young's modulus of elasticity of material B is 15.5 GPa Material B 5 x 10-5 Strain

Physics for Scientists and Engineers with Modern Physics

10th Edition

ISBN:9781337553292

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter18: Temperature

Section: Chapter Questions

Problem 16P: Review. On a day that the temperature is 20.0C, a concrete walk is poured in such a way that the...

See similar textbooks

Similar questions

Use the graph in Figure P14.46 to list the three materials from greatest Youngs modulus to smallest. Explain your reasoning. FIGURE P14.46
The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27
Review. On a day that the temperature is 20.0C, a concrete walk is poured in such a way that the ends of the walk are unable to move. Take Youngs modulus for concrete to be 7.00 109 N/m2 and the compressive strength to be 2.00 109 N/m2. (a) What is the stress in the cement on a hot day of 50.0C? (b) Does the concrete fracture?
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
Bone has a Youngs modulus of 18 109 Pa. Under compression, it can will island a stress or about 160 106 Pa before breaking. Assume that a femur (thigh bone) is 0.50 m long, and calculate the amount of compression this bone can withstand before breaking.
The rubber blocks shown are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 336 N causes the upper frame to be deflected downward by 5.5 mm. Determine the shear modulus Gof the rubber blocks. Assume a = 10 mm, b = 22 mm, and c = 27 mm. Double U anti-vibration shear mount b P Rubber block dimensions Shear deformation of blocks Answer: Shear Modulus G = i MPa.
Sample of timber with length of 1.1 m. Find the width and thickness (b, d) with logical thickness that give the modulus of rupture =0.75 MPa and failure load (P = 500 N). If you know that load span in flexural is (L= 1 m). - Width of sample? P L/2 Your answer Depth of sample? L/2
Problem 1 ▪5-1. A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12 ksi. If the diameter of the shaft is 1.5 in., determine the maximum torque T that can be transmitted. What would be the maximum torque T' if a 1-in.-diameter hole is bored through the shaft? Sketch the shear-stress distribution along a radial line in each case. T
i In. V:Y homewo... > Homework Ql: A specimen made from Titanium with diameter 4 mm subjected to force of 2500 N. The specimen extended by 0.422 mm. If the young modulus is 107 GPa. Find the gauge length of specimen. Q2: A road of stainless steel subjected to a tensile test, and the following result were obtained. Yield load = 175 KN and extension = 0.33 mm Max, Joad = 315 KN and max. extension 7.4 mm Original dia. = 16 mm and breaking dia. = 12.4 mm Original length = 80 mm Find: 1-Max. tensile strength 2-Young modulus 3-Percentage of elongation 4- Percentage of reduction in area II >
Two triaxial tests were performed on two prepared samples of the same slightly altered granite. At a confining pressure of 22 MPa, the first sample failed at 78 MPa. Then at a confining pressure of 47 MPa, the second sample failed at 200 MPa. a. Plot the two test results on a shear stress-normal stress diagram and draw the Mohr (Mahr-Coulamb) envelop b. Determine the value for the limestone. C. What is the So value?
The elastic portion of the tension stress- strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gauge length of 50 mm and a diameter of 12.5 mm. The shear modulus is Gal = 28 GPaGPa. (Figure 1) If the applied load is 49 kN, determine the new diameter of the specimen. Express your answer to THREE DECIMAL PLACES σ (MPa) 500 0.00614 € (mm/mm)
A material with a rectangular cross-section of 5 mm by 10 mm is loaded in tension with a force of 16 kN. A strain gauge bonded to the material measures a strain of 800 microstrain when the sample is loaded. Calculate Young's modulus of the material, measured to the nearest GPa (GN/m2) and enter your answer in the box below. Young's modulus: GPa