The given truss below is loaded vertically downward with 4KN and 8KN at points C and D, respectively, as shown. A model of the truss was made in a laboratory, and it was found out that the values of internal forces in members A-L, A-B, and B-K are as indicated in the table. If the vertical reactions at A andG are 6.667 KN and 5.333 KN respectively, complete the table and answer the succeeding questions. Approximate all answers up to three decimal places. 8 kN 4 kN E B В F 3 m A G K J I H 12 m, 6 @ 2 m Experimental 13.533 Percent Error Member Computational A-L А-В 14.680 В-К 0.012 What is the behavior of the internal reaction of Member A-L? O Tension O None of the choices. O Compression

The given truss below is loaded vertically downward with 4KN and 8KN at points C and D, respectively, as shown. A model of the truss was made in a laboratory, and it was found out that the values of internal forces in members A-L, A-B, and B-K are as indicated in the table. If the vertical reactions at A andG are 6.667 KN and 5.333 KN respectively, complete the table and answer the succeeding questions. Approximate all answers up to three decimal places. 8 kN 4 kN E B В F 3 m A G K J I H 12 m, 6 @ 2 m Experimental 13.533 Percent Error Member Computational A-L А-В 14.680 В-К 0.012 What is the behavior of the internal reaction of Member A-L? O Tension O None of the choices. O Compression

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rigid arm AB is subject to a downward force F=270 lbf. It is supported by asquare shaft journal bearing at A and a cable BC.A. Draw a clear and large free-body diagram (FBD) to show all reaction components on AB. Ifany are not engaged, cross them out and add the note “N.E.” for “Not Engaged.” You do NOTneed to set up any equations or solve for any of the reactions.B. Find the unit vector for cable BC.
The truss shown is used to support a 11 kg block with a pin at A and a roller at E. Given a = 1.1 m, b = 0.7 m, c = 1.2 m and d = 1.2 m find the Internal forces in members AB, BD, BC and Co. b d A E The force in member AB Is The force In member BC Is The force In member BD Is The force In member CD Is B D C N In (Click to select) (Click to select) N In N In (Click to select) IN In (Click to select) (Click to select) tension compression V V
An L-shaped bar is supported by a bearing at A and a smooth horizontal surface at B. Take the value of Fto be 720 N. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 1.5m 1.5m 2m Determine the reactions at A and B. (Do not include a minus sign in your response.) The y component of the reaction force at A is [ NT. The z component of the reaction force at A is N✓. The reaction moment at A about the y axis is N-m . The reaction moment at A about the z axis is N.m O The y component of the reaction force at Bis NT.
The rigid body is supported by a hinge at A and a cable at C. The hinge resists 5.5m translation in all three coordinate directions and rotation in the x and y directions. The 260 N force is in the -x direction and acts at the center of the 3m body. Find the tension in the cable and the components of the support C 2.5m 260N reactions at A. Your answer should include a properly Ilm annotated FBD. B 3.Im
0.8 m 0.8 m 800 N 600 N B 0.4 m 0.4 m y A bent rod is supported by the roller at B, and the smooth collar at A. Find the reactions at all the supports for the loading shown.
The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB, which is controlled by the hydraulic cylinder BC. There is an identical linkage on the other side of the bulldozer. Applied loads shown are for both linkages and F = 751 kN. Determine the magnitude of the pin reaction at A in kN.Determine the magnitude of the pin reaction at B in kN.Determine the magnitude of the pin reaction at C in kN.Determine the pressure in hydraulic cylinder BC in Pa if the cylinder has a diameter of 80 mm.
A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 184 lb, is applied, what are the reactions at the thrust bearing and in the cable. The dimensions shown are a = 8.7 ft, b = 6.4 ft, and c = 4.5 ft. y N
Determine the tension in the rope at point A and the reactions at the pin support at point B. (The 600 lb force points downward to the left on the figure.)
A12-ft wooden beam weighing 80 lb is supported by a pin and bracket at A and by cable BC. Find the reaction at A and the tension in the cable. 6 ft A ft 6 ft 80 Ib Match each item to a choice: Ax Tension on Cable Ay Choices:
W2 acts at the center G of the bar. Find the cables' tensions and the reactions at ball and socket O. W1 is 515 N. W2 is 190 N.
Determine the reactions at supports for the following Figures. A 40 kN/m -8 m B. 3 m 20 KN 150 kN m
The radius of pulleys C and B are 125mm and 250mm,respectively. Given that TB=T'B=90kN and TC=T'C=150kN, find the reactions of supports A and D.