The fuel gage for a gasoline tank in a car reads proportional to its bottom gage. The tank is 35 cm deep and accidentally contaminated with 3 cmof water. Specific gravity of gasoline is 0.68. If the tank is accidentally contaminated with 3 cm of water, how many cm of air remains on top of thetank when the gage reads "FULL"?

Pressure when tank is fully filled with gasoline PG=γgh PG=0.68×9.810.35m=2.34kpaPressure of water…

Answered: The fuel gage for a gasoline tank in a…

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter11: Temperature And Temperature- Related Variables In Engineering

Section: Chapter Questions

Problem 24P

See similar textbooks

Similar questions

Determine the freak point dosage of chlorine given the data below which was obtained from chlorination experiment. 5 6 7 Dosage(mg/L) Required Cl₂Cmg/L 0.2 0.45 1.05 2.75 4.5 5.15 6.03 1 2 3 4
The fuel gage for a gasoline (sp.gr.=0.68) tank in a car reads proportional to itsbottom gage. If the tank is 30 cm deep an accidentally contaminated with 2 cm of water, how many centimeters of gasoline does the tank actually contain when the gage erroneously reads “FULL”?
The fuel gage for a gasoline (sp. gr. = 0.68) tank in a car reads proportional to its bottom gage. If the tank is 30 cm deep an accidentally contaminated with 2 cm of water, how many centimeters of gasoline does the tank actually contain when the gage erroneously reads "FULL"?
Task 3: Fluid Mechanics Lab Meters You studied the SAYBOLT viscometer in the fluid mechanics lab to determine 20W50 Motor Oil viscosity. Follow the following steps to do your task. HEATING UNIT THERMOMETER LIQUID BATH Fluid CONTAINER 60 cC CORK ŘESERVOIR Figure 4: Schematic for SAYBOLT viscometer. a) Illustrate the results of the viscosity test of the above motor oil then fit the viscosity function of temperature to the following logarithmic quadratic correlation as described below. Find the values for the constants a, b, and c. Take Ho at T, = 0°C. a + b| + T Mo b) What is the viscosity of the used motor oil at 280 K, 305 K and 320 K? You can use the above equation
Mr.X performs the laboratory test and determines that 12 mg/l of alum dose is required to treat the water. What is the quantity of alum required to treat 14 million liters of water per day at a treatment plant. Also determine the amount of carbon dioxide gas produced per liter of water during treatment. B I U GGG 25 85 ET M 69
Question 02 Define by which curve the relation between amount of energy absorbed and test temperature is shown, why? Energy absorbed B Temperature
This question is for Jisha, Civil Engineering 2) Mr. X performs the laboratory test and determines that 12 mg/l of alum dose is required to treat the water. What is the quantity of alum required to treat 14 million liters of water per day at a treatment plant. Also determine the amount of carbon dioxide gas produced per liter of water during treatment.
Calculate length of the pipe required to bring down the concentration of chlorine from 6x105 CFU/L to the permissible value of 2500 CFU/L. It is given that the velocity of flow through the pipe is 0.7 m/s and the rate constant is 0.25.
A certain jet fuel has a kinematic viscosity of 1.2 x 10-6 m2/s. If the fuel is being delivered to the engine at 200 L/min through a steel tube (Diameter = 22.10 mm), compute the Reynold number and identify the type of flow either laminar or turbulent?
The most dangerous particles in polluted air are those with diameters less than 2.5 μm because they can penetrate deeply into the lungs. Part A A 15-cm-tall closed container holds a sample of polluted air containing many spherical particles with a diameter of 2.5 μm and a mass of 1.6 x 10-14 kg. How long does it take for all of the particles to settle to the bottom of the container? Express your answer in minutes. At = Submit - ΑΣΦ A ➜ C Previous Answers Request Answer * Incorrect; Try Again; 4 attempts remaining < Return to Assignment Provide Feedback ? min
in a test to determine the discharge coefficient of a 60 mmx 15 mm Venturi meter, the total weight of water passing the meter in 5 minutes was 350 kg. A mercury differential" gauge connected to the inlet and throat of the meter showed an average mercury difference during that time of 360 mm. Calculate the meter coefficient. Round off your answer to ane decimal place. Answer: Cv
Two milliliters of 0.025molars potassium iodate solution was used to standardized the sodium thiosulfate used in dissolved oxygen (DO) determination. If 19.4mL of the sodium thiosulfate solution was used, what is the corrected established relationship? (pre-established relationship: 10mL sodium thiosulfate = 1 ppm DO) 10mL Na2S203 solution = 0.104 mg/L DO 10mL Na2S203 solution = 1.856 mg/L DO 10mL Na2S203 solution = 0.224 mg/L DO O 10mL Na2S203 solution = 1.232 mg/L DO

SEE MORE QUESTIONS

Recommended textbooks for you

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

SEE MORE TEXTBOOKS