The frame shown below is fixed at point Q and subjected to the axial load at free end in both points A and B, if (a) (Es/Ec) = 8, (b) direction x and y axis. Determine the actual stresses acting (Es/Ec) = 0 Q1) The frame shown below is fixed at point Q and subjected to the axial load at free end in bothdirection x and y axis. Determine the actual stresses acting at points A and B, if (a) (Es/Ec) = 8, (b)(Es/Ec) = 0.1.5m50KN45kN25cm -25kNA50cm3m10cm# 25mm

Consider the free body diagram; Calculate the moments at y-axis; My1=45×0.125,My2=25×0.125…

The frame shown below is fixed at point Q and subjected to the axial load at free end in both points A and B, if (a) (Es/Ec) = 8, (b) direction x and y axis. Determine the actual stresses acting (Es/Ec) = 0

The frame shown below is fixed at point Q and subjected to the axial load at free end in both points A and B, if (a) (Es/Ec) = 8, (b) direction x and y axis. Determine the actual stresses acting (Es/Ec) = 0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STEEL DESIGN include free body diagram and detailed solution.
Question 5 Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section instead of a rectangular section. v Maximum Bending stress of a cross section. B. Tension and bending force. C. 1m form the supports - v If a simply supported beam is subjected to a distributed load, where are you most likely to find tension bending cracks. D. At Midspan - v Ifa simply supported beam is subjected to a distributed load, where are you most likely to find shear cracks. E. Midspan at the bottom v The bending stress in a section can be reduced by using a F. Midspan at the top v Shear stress can be increased by the width of a section. G. At the supports. v The shear force in fasteners. H. Reducing the width of a section. v Moment couple on a section. 1. using a rectangular section instead of an l-section J. Shear flow K. Increasing the width of a section. L. Only at the section sides touching the NA M. In between the NA and the top/bottom fibres N. Usually at the NA…
The allowable shear stress is τallow=895 psi�allow=895 psi. The supports at A� and B� are smooth
Design the shear reinforcement for the beam shown in figure below assuming it resists an ultimate shear force at distance d from the face of the support of 450 kN. The characteristic material strengths are fok= 25 N/mm²and fm = 500 N/mm² 450 kN d= 500 mm -4H25 b= 300 mm
6
A 62.6-kN vertical load P is applied at the corner of the square cross section of the steel compression member AB, which is free at its top A and fixed at its base B. Knowing that for the grade of steel used oy=345 MPa and E= 200 GPa, and using the allowable-stress method, determine the smallest allowable dimension d. B D 1.5 m The smallest allowable dimension dis mm.
Consider the loads of the figure to be axially applied at sections B, C, and D to the concrete structure supported at A. IW E F P G 5 kN 5 kN A Determine P in kN when member BC is 24 mm in diameter, the axial stress in section F is 588 MPa, and W 309822 N. = 10 kN C 10 kN Rigid -bearing plates
a) Two bars of different size form a pin-connected frame that supports a Load 'P' at point A as shown in the Fig. 3. What safe load P (kN) can be applied if the allowable stress of 120 MPa is not to be exceeded? Assume buckling has been prevented. Allowable stress is based on a factor of safety of 2.0. Cross sectional area of the rods AB and AC are given in the adjacent table as per last digit of Roll number. What is the failure load? Last digit of Area of AB | Area of AC Roll No. 1, 2, 4 & 7 200 mm 230 mm“ 3, 6 & 8 160 mm- 190 mm² 5, 9 & 0 180 mm 210 mm 2400 1600 Fig. 3 b) Two square bars are of equal length but have different size as shown in Fig. 4. Compare the maximum stress in the two bars if they are to receive the same input of energy from axial load. Given, m = (2 + last digit of your roll number). 2a 5.x m.x Fig. 4 last digit of roll=1
A wooden frame shown below is supported by a tie rod CF and a pin support at A. The diameter of the tie rod CF is 30 mm, and the cross-sectional area of member BD is 900 mm?. The diameters of the pins at A and D are 8 mm and 12 mm, respectively, and each pin is subjected to double shear. If the weight of the bucket hanging from end E is 3 kN, determine (a) The axial stresses in tie rod CF and member BD. (b) The shear stresses in pins A and D. - 0.6 m-0.6 m→ D E 0.6 m V30B 1.2 m F
The assembly shown below is pinned at A & C and A & C are subjected to a double shear. Let each pin diameter be 18 mm, and P = 20 kN. Find the:a) Force at the rod BC (kN) and force acting on pin A (kN)b) Average shear stress at A (MPa), and average shear stress at C (MPa)
Find the maximum tensile and compressive normal stresses in the beam below. Mark their locations along the height of the cross section and along the length of the beam. (Note: The centroid is located 4.423in from the top of the cross section and I= 42.0 in*.) W= 1k/ft 6k 10' 5' 4423" 8.75 M (k-t) -12.5 Cross section
Determine the shear stress in plane AB of the beam section shown if it is subjected to a shear force V. Assume that the neutral axis passes through the A-B axis. Usar los siguientes datos: H1 = 15 in. H2 = 20 in. H3 = 8 in. W = 22 in. H2 H3 V = 300 Kips H1