Please make solution and answer clear >i will vote it up, need your help ASAP. TABLE 1-2 Minimum Densities for Design Loadsfrom Materials*AluminumConcrete, plain cinderConcrete, plain stoneConcrete, reinforced cinderConcrete, reinforced stoneClay, dryClay, dampSand and gravel, dry, looseSand and gravel, wetMasonry, lightweight solid concreteMasonry, normal weightPlywoodSteel, cold-drawnWood, Douglas FirWood, Southern PineWood, sprucelb/ft³1701081441111506311010012010513536492343729kN/m³26.717.022.617.423.69.917.315.718.916.521.25.777.35.35.84.5*Reproduced with permission from American Society of Civil EngineersMinimum Design Loads for Buildings and Other Structures, ASCE/SEI 7-10.Copies of this standard may be purchased from ASCE at www.pubs.asce.org. PROBLEM 4The frame is pin supported at D and E and a fixed support at A. All dimensions are inmeters. Use Moment Distribution Method. Use 3 iterations only.a) Determine the Distribution factor for CEb) Determine the Fixed End Moments at CB. (Answer should be in kN-m)c) Determine the moment at point A of the frame shown in figure. (Answer should be inkN-m)7m24 kN/mB EI2EI1m5 m2EID7mEI7mE

a) Distribution factor(DF) is used to determine the proportion of the moment carried by the beam. It…

The frame is pin supported at D and E and a fixed support at A. All dimensions are in meters. Use Moment Distribution Method. Use 3 iterations only. a) Determine the Distribution factor for CE b) Determine the Fixed End Moments at CB. (Answer should be in kN-m) c) Determine the moment at point A of the frame shown in figure. (Answer should be in kN-m) 7m 24 kN/m B EI 2EI 2EI 7m EI E|

The frame is pin supported at D and E and a fixed support at A. All dimensions are in meters. Use Moment Distribution Method. Use 3 iterations only. a) Determine the Distribution factor for CE b) Determine the Fixed End Moments at CB. (Answer should be in kN-m) c) Determine the moment at point A of the frame shown in figure. (Answer should be in kN-m) 7m 24 kN/m B EI 2EI 2EI 7m EI E|

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Analysis the frame shown in figure by MOMENT DISTRIBUTION METHOD and draw BMD. Assume EI is constant. 5KN/M 20KN 5M GM- -41M A
USE SLOPE DEFLECTIO METHOD. From the indeterminate frame shown, find the moment at B acting in M member AB, BA, in kNm. EI is constant. 60 kN B 5 m A 45 kN m 6 m 5 m D 4 m E
USE MOMENT DISTRIBUTION METHOD. Given the indeterminate beam, find the reaction at B in kN. EI is constant. A 5KN/m 5m B 2m 10 KN 3m
Use Slope-Deflection Method or Moment Distribution Method to solve for the unknowns on the 120mm x 200 mm beam shown in the figure. E = 80 GPa. For MDM, use at least 4 iterations (up to bal 4). a. Fixed-end moment (FEM) at joint A on member AB. Indicate negative if counter-clockwise. b. Moment at A in kN-m. Indicate negative if counter-clockwise. c. Moment at C in kN-m. Indicate negative if counter-clockwise. 20.6 kN 33.8 kN/m 3.3 m 3.7 m 3 m
2. For the overhanging beam shown, determine the maximum value of Eld between the supports using moment-area method. El is constant 3600 N/m 1200 N/m В A 4 m 2 m
using moment distribution method. determine the moment mcb in the beam. the beam has a constant EI. input the magnitude in kN-m
Use Slope-Deflectian Method or Moment Distribution Method to solve for the unknows on the 120mm x 200 mm beam shown in the figure. E = 80 GPa. a. Fixed-end moment (FEM) at joint A on member AB. Indicate negative if counter-clackwise. b. Moment at A c. Moment at C
USE SLOPE DEFLECTIO METHOD. From the indeterminate frame shown, find the moment at C acting in member BC, MCB, in kNm. EI is constant. 60 KN B 5 m A 45 kN/m ↓ 6 m 5m D 4m E
2. Determine the location of the center of gravity of a wire with uniform cross- sectional area and specific weight., shown in the figure below. The wire is in the form of a broken line P, P2 P3 P4, with P:(-3, 7), P2(-1, 1), P3 (3, 5) and P. (5, 3). C.G. (0.30, 3.60) Pi-3, 7) P(3, 5) M(-2, 4) 8 M5(1, 3) XM(4, 4) PA(5, 3) P2(-1, 1)
Computer Study—comparison of approximateanalysis with an exact analysis. (a) Use approxi-mate analysis to compute the reactions and drawthe moment diagrams for column AB and girder BC of theframe in Figure P13.20, and draw the deflected shape.Consider column bases are fixed. (b) Repeat the computa-tions with pinned column bases at A and D. (c) Comparethe results with the exact analysis using a computer soft-ware. Consider columns A = 13.1 in.2, I = 348 in.4; girderA = 16.2 in.2, I = 1350 in.4. Use E = 29,000 kips/in.2forall members.
USE SLOPE DEFLECTIO METHOD. From the indeterminate frame shown, find the moment at C acting in M member CE, CE, in kNm. EI is constant. 60 kN B 5 m 45 kN/m 6 m 5 m 4m E
I have worked out reaction forces Ra and Rb, -= 3060N and 1710N respectively. could you please help with bending in the beam, and a ough sketch if you have the time please, Thanks