The force F = {25i – 50j + 10k} lb acts at the end A of the pipe assembly. Determine the magnitude of the components F, and F2, which act along AB and perpendicular to it.

Q: Express and identify the resultant of the two forces and one couple shown acting on the shaft angled…

A:

Q: Determine the ratio of the factored compressive load and the design compressive strength.0…

A: Answer  Calculation of ratio of factored compressive load and the design compressive strength For…

Q: of tion Given the horizontal beam AB with two supports Pin A and Roller B. The system is subjected…

A:

Q: A - determine force in member AB B - determine force in member AC C - Determine force in member AD

A:

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: Determine the following  a. Resultant force at C b. Resultant force at D c. Resultant force at E…

A: Determine the following. a. Resultant moment at A b. Resultant moment at D c. Resultant moment at E

Q: Question 2 Frame ABCDE shown in Figure Q2 is supported by a fixed connection at B, roller at D and…

A:

Q: Calculate the internal forces on the section C and construct the M diagram. 8 A a B a

A:

Q: F2 F1 E 3m 3 m

A:

Q: Determine the force in the member connected joint 7 to joint 9 for the truss shown below if P = 10…

A:

Q: The shaft supports the two pulley loads. Determine the equation of the elastic curve. EI is…

A:

Q: Q5. The system shown consists of three bars having different flexural rigidities with El2 = 2El, and…

A: Given: Flexural Rigidity EI2 is equal to twice of Flexural Rigidity EI1 i.e EI2=2EI1

Q: cylindrical tank 3m in diameter and 7m high is filled with oil (sg=0.85). The tank is provided by…

A:

Q: Determine the couple moment acting on the pipe shown .Segment AB is directed 30° below the x–y…

A: The couple moment acting on the pipe will be same as calculated about any point. So let us consider…

Q: A short rectangular column 300 mm on one side and 400 mm on the other side.  It is reinforced with…

A:

Q: A 200-lb force (P) directed vertically downward is applied to the toggle vise at C. Knowing that…

A: Given Data : Length of AB= 4 in Length of BC= 6 in length of BD= 6 in Force (P)= 200 lb

Q: 6 m 1 5 m ho = 2m ihD 4 m B

A:

Q: 9. Determine the Moment of a Force at A. Consider clockwise to be positive. F=12N 12 1 12/2 • 0 A 1…

A: solution  divide the force F into components finding angle made by F with horizontal

Q: C. (8-1²) dr = r²³ sine do fo 2

A:

Q: Determine the force in member CD in kN when P = 35 kN. Express your answer in 2 decimal places.…

A: Determine force in member CD,Fcd=?

Q: 5. Bar ABD and bar CEF are connected using a pin at point C and a strut member BE to support a 9000…

A:

Q: Determine the force in member AB, FE and CD using method of section. A |– 3 m →✦✦✦▬▬4 m —✦✦✦▬ 3 m →|…

A:

Q: displacemen steel member has a cross-sectional area of 300 mm². Use the method of virtual work

A:

Q: Two rods vertically connect beams AB and CD as shown in the figure. Point Ais fixed supported wnile…

A:

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: D, 3 Use the diagram shown above. Given • D= 10 ft • D2= 7 ft • D3=4 ft • W - 500 #/ft Solve for the…

A: Figure is as shown

Q: Problem 2: Find the force in bar DB. (AE = constant.) 30k 7' D B 12' 12' 24'

A:

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

A:

Q: P₁ kN- P₂ kN- Determine (approximately) the reactions at the base of the columns of the frame shown…

A:

Q: 4m 60⁰ 2kN C 60⁰ 2kN B 8m 30⁰ 2kN A

A: Cut the x-x plane as shown in below solution. Applying equilibrium equation in both x and y…

Q: . Discuss each component of the building envelope system.

A: Hi! Thank you for the question.  As per the honor code, we’ll answer the first question since the…

Q: A rigid beam loaded with negligible mass is pinned at B and is supported by two indentical rods,…

A: Take Moment at B zero Deflection will be in ratio of distance from B

Q: 800lb 60 12' 12 FORCE Ibs A MA= Fxd Couples F= F.Cos( e ) F= F.Sin( e) Forces 100lb/ft

A: Given data  Point load and UDL Length of span.

Q: Determine support reaction .Take P=10 KN

A: Apply equilibrium to solve the reaction . Their are three equilibrium condition with help of…

Q: Given v, = 25m/s %3D S.g.= 0.83 Find the force required plate d=somm jet

A: given :-

Q: pinned atone end and supported by two Roads, The beam 20as initially hORLZontal before the load ras…

A: P=120kN

Q: (a) For the case of no sway, calculate the value of stiffness (K) and distribution factor (DF) for…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: T 2m 3 m B 10 kNE A 20 kN F 2 m2 m C D

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.