The following three parallel-connected three-phase loads are fed by a balanced three-phase source: Load 1: 250 kVA, 0.8 pf lagging Load 2: 300 kVA, 0.95 pf leading Load 3: 450 kVA, unity pf If the line voltage is 13.8 kV, calculate the line current and the power factor of the source. Assume that the line impedance is zero.

The following three parallel-connected three-phase loads are fed by a balanced three-phase source: Load 1: 250 kVA, 0.8 pf lagging Load 2: 300 kVA, 0.95 pf leading Load 3: 450 kVA, unity pf If the line voltage is 13.8 kV, calculate the line current and the power factor of the source. Assume that the line impedance is zero.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23MCQ: In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. ' qu V = 1.05200 0.01+ j0.025 300 + j200 MVA 3 0.015 + j0.035 150 MW 200 + j150 MVA 0.01 + j0.03 |V = 1.03 The admittance matrix (Y_bus)? The bus power in per-unit?
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. ' V, = 1.05200 0.01 + jo.025 300 +j200 MVA 3 0.015+j0.035 150 MW 200 +j150 MVA 4 0.01 + j0.03 |V2 = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03
VRY = 220 cis 0°, VYB = 220 cis -120° and VBR = 220 cis -240°. IR = 10 cis 0°. The load isbalanced and delta connected. Determine the: (a) Impedance per phase (b) Current perphase (c) Line currents.
3. The single-line diagram of a three-phase power system is as shown in Figure Al-3. Impedances are marked in per unit on a 100-MVA, 400-kV base. The load at bus 2 is S2 = 15.93 MW – j 33.4 Mvar, and at bus 3 is S3 = 77 MW +jl4 Mvar. It is required to hold the voltage at bus 3 at 40020° kV. Working in per unit, determine the voltage at buses 2 and 1. V2 V1 V3 j0.5 pu j0.4 pu S2 S3 Figure A1-3
The plant capacity of a 3-phase generating station consists of two 8 MVA generators of reactance 14·5%each and one 4 MVA generator of reactance 9·5%. These are connected to a common bus-bar fromwhich loads are taken through a number of 3 MVA step-up transformers each having 4% reactance.Determine the MVA rating of the circuit breakers on (i) L.V. side and (ii) H.V. side. Reactances givenare based on the MVA of each equipment. [(i) 15·24 MVA (ii) 50·25 MVA]
A balanced Y-connected generator with terminal voltage Vbc 5 200/08 volts is connected to a balanced-D load whose impedance is 10/408 ohms per phase. The line impedance between the source and load is 0.5/808 ohm for each phase. The generator neutral is grounded through an impedance of j5 ohms. The generator sequence impedances are given by Zg0 5 j7, Zg1 5 j15, and Zg2 5 j10 ohms. Draw the sequence networks for this system and determine the sequence components of the line currents.
The single-line diagram of a subtransmision system is presented in the figure below. At point B a three- phase short circuit has occurred. Calculate the voltage at points A, B, C and D. Three phase short circuit Infinite bus D +j0.2 j0.67 +10.70 +j1.05 V-1.00 pu
Draw Wye- Delta three phase transformers connection ( no-load and full-load) in Lt-spice
A workshop from a 231/400 V transformer center with a 3-phase and four-conductor underground cablefed. The resistance of the phase conductors is 0.035 ohms and the resistance of the neutral conductors is 0.05 ohms.25 kVA at 0.8 reverse power factor from R phase of the supply line, 0.8 forward power factor from S phase 15Fully ohmic loads of 10 kVA are drawn from kVA and T phases.(a) Find the currents flowing through the phase conductors and neutral conductors.(b) Voltage drops between the transformer substation and the workshop and at the load terminals.calculate the voltages(c) Plot the supply line currents and phase voltages phasorally.
VA-120 V4120 Z₁ volt In lc c ZA Three-phase source Feeder lines Balanced load In the above circuit diagram, we have source impedance Zg = 0.05+j0.15 ohm, Z₁ = 0.1+j0.2 ohm and per phase impedance in the balanced Delta connected load, Z₁ = 12+j9 ohm. RMS value of source voltage is 200 volt. Phase sequence is as shown in the diagram. RMS value of current Ic= ampere Phase angle of le= degree RMS value of line voltage VCA = B JAB Inc ICA