The following particulars refer to a two- Tow velocity- Compounded Impulse wheel which foms of a Q. -co the first Stage combination turbine: 630ml : 125 m/s Steam Velocity at noz2le Outled: Me an blade velocity 16° 18° Nozzle cungle Outlet augle, first yau d Dutlel angle, fixed quide bades: 22" sutfel cugle,tlcond 2ow of Maring 6ladsi 36 Steam flow rate blade: mo uing The radio of the relative velocity ot outlet o that at înlet ia 0.84 for deteomine all the table. 92. The velocity of whizd. 279/augebiaf 6 The axial thrust on the blades thrust on the blade s the pred developed. the lading efficiency.

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: Find 150Am 120mm V- 100 mm

A: Consider the below diagram,

Q: Consider the equation for angular twist due to torsion. Imagine you are designing a solid round…

A: The angular distortion of an item caused by a couple of twisting torques is known as the angle of…

Q: (b) Compute the internal torque exerted on gear A (TAC), gear C(TcD) and gear D (TDB). (c) Sketch…

A:

Q: y' = -y tan x, y(0) = 2

A:

Q: For the frame shown below, Is supported by pins at C and D. Determine the magnitude of reaction at C…

A: Consider the free body diagram of the member CBA as shown below.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 2.36x178×106 1- 1 0.9x300x368²×30 Prequired 400 (1.18 30)

A: Given Data⇒

Q: ldentify the valvetrain components in the drawings. Place the identifying letter next to the name of…

A: Valve train get together for a gas powered motor contains a typical transporter which upholds the…

Q: The equation of the unit circle is _______________.

A:

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: Q.2 A cantilever beam of length / = 5 m, flexural rigidity El in MPa, and mass m = 1950 kg carries…

A:

Q: 200 mm В

A:

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: What is the length and wall thickness of the vertical bear

A: For figure 2,  drawing and the type of symbols present

Q: Fload/8 Fload/4 ffort = Fload/8

A: According to the details provided in the question, we need to calculate  we need to find all forces…

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: For figure (4): The ring is subjected to two forces (F, and F2). Suppose that the resultant force…

A: Given data:

Q: Choose three types of Reuleaux lower pairs, and answer the following, F.1 Write down their names?…

A:

Q: A multi-stage pump, 260 gpm capacity is installed in a well 27 ft below the static water level.…

A: Given data:  The capacity of the pump is given as Q = 260 gpm = 0.579 ft3/sThe total discharge head…

Q: Incorrect please resolve both parta

A: To calculate the surface temperature of the tank when it is passed through water and to calculate…

Q: Crossed center lines are used in the .. . view Longitudinal Horizontal Circular All

A: Solution:

Q: Calculate the number of degrees of freedom The value must be a number 11 Calculate the number of…

A: Full joint is the joint which has area or surface contact, and half joint is the joint which has…

Q: A piston-cylinder device contains 1.5 kg of steam at 300°C and 0.4 MPa. Steam is cooled at constant…

A:

Q: M, B

A: Given data, The reaction at A and B can be calculated as -

Q: What is the location of FR, i.e., the distance d? A M 3 m 3 m F. R B

A:

Q: What is the normal force applied to the block?

A:

Q: Through the two pipes in Figure 6 flow equal flows of water. data: Pipe diameter No. 1: 200 mm -…

A:

Q: The point 1/4 of the way from (1,-3, 1) to (7,9, –9) is A. (4,3,-4) O B. (3/2,3,-3/2) OC.…

A: A point's coordinates are a pair of integers that define its precise position on a two-dimensional…

Q: Starting from rest, Block A moves down the inclined plane with velocity given by 3t“, where t is in…

A:

Q: How do you know that it is -1.2? What determines the sign?

A: Given: How do you know that it is -1.2? What determines the sign?

Q: 7 panels at 4 m B C D 4 m A H. 8 kN 8 kN

A:

Q: why is F3 0

A: Hydrostatic Force- A resultant force which acts on a submerged surface due to the pressure loading…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.