The following data for a closed traverse is as follows. Determine the area of the closed traverse

Q: different methods of contouring

A: Methods of contouring 1- Direct method- It finds horizontal and vertical points on contour lines. 2-…

Q: Describe possible errors which are encountered during this survey and how they can be minimised.

A:

Q: 6. A closed traverse with 5 corners has field measured interior angles at each corner as follows,…

A:

Q: 1. Hydrographic surveys deal with the mapping of A large water bodies Ⓡ heavenly bodies O…

A: Given:It is asked to select the correct option

Q: Problem 2. Given the following traverse notes for a closed traverse, LINES AB BC CA AZIMUTH 225°…

A:

Q: A traverse line was measured in three sections: 295.85 m at slope 8°45', 4°29' and 373.48 m. at…

A:

Q: b) Determine the area enclosed by a closed traverse ABCDE from the followin data. (* represent…

A:

Q: A travers survey is a method of determining the location of lots and boundary markers. The boundary…

A: This question is from surveying _Traverse survey    Our aim is to list the some of negative…

Q: Compute the closure error in closed-polygon traverse if you know the relative precision (1/6000) and…

A: Surveying mainly considers the branch of measurement of the points on the ground surface for the…

Q: Given in the accompanying tabulation are the observed data for a traverse obtained from a transit…

A: To Determine Linear error of closure and To balance the traverse using Compass Rule.

Q: Find the area by using Double Meridian

A:

Q: 3. Use the given table below and the technique of coordinates to compute the traverse area and plot…

A: The data is given in order to find the area we will use concept of latitude and departures.

Q: SITUATION 6: The data for a closed traverse are as follows: Bearing Course AB BC CD DA S W S 8° 51'E…

A:

Q: There is a three sided plot of land that you need to define. Based upon your field measurements with…

A: Calculating the closure error is necessary to determine whether the closed traverse meets Ohio's…

Q: Refer to the figure, calculate the area (DMD) enclosed by the traverse 1, 2, 3 and 4. Tabulate…

A: The given data is: S. No. Line Length Bearing Whole circle Bearing 1. 1-2 15.12 m N44°13'W…

Q: Given the following tabulated data for a closed traverse, determine the ff: COURSE AB BC CO DA…

A: Given, Tabulated data for closed traverse    To find : Length BC, CD and area of closed traverse

Q: For all the computed values with decimals, use four (4) digits after the decimal. Given in the…

A:

Q: List the examples of closed traverses.

A: A traverse is series of lines end to end connected with each other whose length and bearing are to…

Q: the two sources of Errors in sample surveys.

A: Different sources of errors in sample survey are: 1. Specification error 2. Frame error 3.…

Q: Question 1:  What is the area of each station in square feet?   Question 2: What is the average…

A: Area calculated at stations 0 + 00 , 0 + 47.5 and 0 + 75.9 are 139.04 sq.ft ,57.69 sq.ft and 43.43…

Q: Problem 2. Given the following traverse notes for a closed traverse, LINES AB BC CA AZIMUTH 225°…

A:

Q: Solve the following problems showing your complete solutions. Draw the figure completely labelled…

A: Consider the traverse diagram;

Q: The interior angles of a triangular traverse were repeatedly measured, with the results shown below.…

A:

Q: What is the relative error of closure? O a. Perimeter of traverse/error of traverse O b. Perimeter…

A: The other name for relative error of closure is the degree of accuracy or relative accuracy.…

Q: SITUATION. Given the following corrected data of a close traverse: Course Distance Departure…

A: We can find the area of Traverse by  DMD method (double meridian distance) DPD method (double…

Q: A topographic surveying map using a scale 1cm: 40 m, and with a contour interval of 1.0 m. The…

A: .

Q: Traverse Surveying Question In a closed loop traverse of 1 km total length, the closing errors in…

A: Given data- A closed loop traverse- Total length L=1 km=1000 m, Closing error in departure = 0.3,…

Q: Determine the area of the traverse Survey data : 400 - A (250,80) -B (270,380) -C (50,350) 300 -D…

A:

Q: In civil engineering, a cut or fill is where soil of rock material from/to a hill or mountain is cut…

A: Calculate the depth of cutting or height of filling Distance 8+50 9+00 9+50 10+00…

Q: When we cruise using variable (non-fixed) area points, it is very important to not "miss" a sample…

A: When cruising using variable area plots, the number of sample trees within the plot is determined by…

Q: Using the computed data by Transit Rule, determine the area of closed traverse by using DMD and DPD…

A: Latitude = Lcosθ Departure = Lsinθ Correction in LAT = -(absolute LAT/absolute Sum of latitude) x Σ…

Q: Compute the closure error in closed-polygon traverse if you know the relative precision (1/15000)…

A: Surveying a branch of the construction industry where balancing between different points on the…

Q: Situation 4] Three routes were utilized in a route survey conducted by a taping party. By route 1,…

A:

Area Computations

The area is the mathematical estimation of the inner space occupied by any shape or object and area computation is the evaluation of how much inner space that particular shape or object has utilized. Simple applications include calculating the area of wall for the quantity of paint or plaster to be applied on it, area calculations for construction of a trapezoidal dam and how much material is required, calculating the area of a circle to determine the range or distance of wheels that they are capable of covering due to varied radii and so on.