I.PROBLEM SOLVING.The following are data pertaining to three units in a plant:Unit 1:Min: 150 MWMax: 600 MWC(1) = 0.01562 P₁2 + 79.2 P₁ + 5610 $/brUnit 2:Min: 100 MWMax: 400 MWC(2) = 0.0194 P₂² + 78.5 P2 + 3100 $/brUnit 3:Min: 50 MWMax: 200 MWC(3) = 0.05784 P3² +95.64 P3 + 936 $/brWhat unit or combination of units should be used to supply a load of 550 MW most economically?Support your answer with solution.

I have written this solution as handwritten solution. Hope you find the perfect solution.

The following are data pertaining to three units in a plant: Unit 1: Min: 150 MW Max: 600 MW C(1) = 0.01562 P₁² + 79.2 P₁+ 5610 $/br Unit 2: Min: 100 MW Max: 400 MW C(2) = 0.0194 P₂² +78.5 P₂ + 3100 $/hx Unit 3: Min: 50 MW Max: 200 MW C(3) = 0.05784 P3²+ 95.64 P3 + 936 $/hr What unit or combination of units should be used to supply a load of 550 MW most economically? Support your answer with solution.

The following are data pertaining to three units in a plant: Unit 1: Min: 150 MW Max: 600 MW C(1) = 0.01562 P₁² + 79.2 P₁+ 5610 $/br Unit 2: Min: 100 MW Max: 400 MW C(2) = 0.0194 P₂² +78.5 P₂ + 3100 $/hx Unit 3: Min: 50 MW Max: 200 MW C(3) = 0.05784 P3²+ 95.64 P3 + 936 $/hr What unit or combination of units should be used to supply a load of 550 MW most economically? Support your answer with solution.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
In the circuit in Figure 2, the capacitor andThe circuit of resistance is defined as a load circuit.a) Find the average power dissipated by the load circuit?b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Interpreting the results obtained?c) In the circuit in Figure 2, with a resistance of 80 ohms 23?A coil of is connected in series. In this case,calculating transformer ratio () to optimize power delivery to the load? Obtainedinterpreting the result?d) Calculate the distributed load complex power and reactive power in the newly learned circuit?
Step by step solutions please
The efficiency of any real wind turbine O a. can be more than 59.3% O b. can be less than 59.3% O c. is nearly 100% O d. is always equal to 59.3%
What will be the value of the twiddle factor: W42
a) What is the peak voltage across R2? b) What is the RMS value of I1?
Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
Computed Rms value (V) 100 E1:A to B E2:A to C 1502 E3:A to D 220. E4:A to F 220 Vac E5:A to G 330 E6:F to G E7:B to C 470 E8:C to D 6802 E9:D to E E10:E to F
The Value of R1 is 39.4Ohms. explain
QUESTION 11 An inductor is connected in parallel with a 6540 resistor and a function generator. The applied voltage is 42V RMS and the total current is 67mA RMS. Find the magnitude of the current through the inductor. Enter your answer in the space provided. Round your answer to one decimal place. Your answer should be in mA but do not enter the unit.
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.