The flat bars shown in parts a and b of the figure are subjected to tensile forces P-3.0 kips. Each bar a has thickness t-0.3in. a. For the bar with a circular hole, determine the maximum stresses for hole diameters d-1.0in. and d-2.0in, if the width b-6.0in. b. For the stepped bar with shoulder fillets, determine the maximum stresses for fillet radii R=0.25in. and R-0.5in, if the bar widths are b-4.0in, and c2.5in.

The flat bars shown in parts a and b of the figure are subjected to tensile forces P-3.0 kips. Each bar a has thickness t-0.3in. a. For the bar with a circular hole, determine the maximum stresses for hole diameters d-1.0in. and d-2.0in, if the width b-6.0in. b. For the stepped bar with shoulder fillets, determine the maximum stresses for fillet radii R=0.25in. and R-0.5in, if the bar widths are b-4.0in, and c2.5in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.10.1P: The flat bars shown in parts a and b of the figure are subjected to tensile forces P = 3.0 kips....

See similar textbooks

Similar questions

Solve the preceding problem if the element is steel (E = 200 GPa. p = 0.30) with dimensions a = 300 mm. h = 150 mm. and c = 150 mm a n d with the stresses (T( = —62 MPa, r. = -45 MPa, and = MPa. For part (e) of Problem 7.6-3, find the maximum value of u. if the change in volume must be limited to —0.028%. For part (0. find the required value of if the strain energy must be 60 J.
The flat bars shown in parts a and b of the figure are subjected to tensile forces P = 2.5 kN. Each bar has thickness t = 5.0 mm. (a) For the bar with a circular hole, determine the maximum stresses for hole diameters d = 12 mm and d = 20 mm il" the width h = 60 mm. (b) For the stepped bar with shoulder fillets, determine the maximum stresses Tor fillet radii R = 6 mm and R = 10 mm if the bar widths are h = 60 mm and c = 40 mm.
A solid circular bar is fixed at point A. The bar is subjected to transverse load V = 70 lb and torque T = 300 lb-in. at point B. The bar has a length L = 60 in. and diameter d = 3 in. Calculate the principal normal stresses and the maximum shear stress at clement 1 located on the bottom surface of the bar at fixed end A (see figure), Assume that element 1 is a sufficient distance from support A so that stress concentration effects are negligible
A circle of a diameter d = 200 mm is etched on a brass plate (see figure). The plate has dimensions of 400 x 400 x 20 mm. Forces are applied to the plate, producing uniformly distributed normal stressescr^ =59 MPaander^ = —17 MPa. Calculate the following quantities: (a) the change in length Aac of diameter at: (b) the change in length Abd of diameter bd; (c) the change At in the thickness of the plate; (d) the change AV in the volume of the plate; (e) the strain energy U stored in the plate; (f) the maximum permissible thickness of the plate when strain energy £/must be at least 784 J; and (g) the maximum permissible value of normal stress axwhen the change in volume of the plate cannot exceed 0.015% of the original volume. (Assume E = 100 GPa and v = 0.34
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A copper bar of rectangular cross section (b = 18 mm and k = 40 mm) is held snugly (but without any initial stress) between rigid supports (see figure). The allowable stresses on the inclined plane pq at mid-span, for which ?? = 55°. are specified as 60 MPa in compression and 30 MPa in shear. (a) What is the maximum permissible temperature rise AT if the allowable stresses on plane pq are not to be exceeded? (Assume a = 17 × 10-6/oC and E = 120 GPa.) (b) If the temperature increases by the maximum permissible amount, what are the stresses on plane pq? (c) If the temperature rises AT = 2SoC how far to the right of end A (distance BL, which is expressed as a fraction of length L) can load P = 15 kN be applied without exceeding allowable stress values in the bar? Assume that a =75 MPa and t = 35 MPa.
-9The stresses acting on element B in the web of a wide-flange beam are found to be 14,000 psi compression in the horizontal direction and 2600 psi compression in the vertical direction. Also, shear stresses of magnitude 3800 psi act in the direct ions shown (see the figure for Problem 7.2-9). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The normal and shear stresses acting on element B are ??x= -46 MPa, sy= -13 MPa, and txy= 21 MPa (see figure for Problem 7.2-10). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A gondola on a ski lift is supported by two bent arms, as shown in the figure. Each arm is offset by the distance b = ISO mm from the line of action of the weight force W. The allowable stresses in the arms are 100 MPa in tension and 50 MPa in shear. If the loaded gondola weighs 12 kN, what is the minimum diameter roof the arms?