The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The couple is positive if counterclockwise, negative if clockwise. A Answers: M= i 1.24 m- L--x 440 N-m 0.44 m kN.m 1.86 KN 72⁰ 1.17 KN 0.18 m 0.18 m DIN

The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The couple is positive if counterclockwise, negative if clockwise. A Answers: M= i 1.24 m- L--x 440 N-m 0.44 m kN.m 1.86 KN 72⁰ 1.17 KN 0.18 m 0.18 m DIN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
thank you can u plz solve f&g now
Topic/s: Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation,Moment of a Force-Vector Formulation, and Principle of Moment. Reminder: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. Thank you.
There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. Problem: A refrigeration cycle uses refrigerant R-134a to cool down water from 40°C to 20°C. The refrigerant R-134a enters the cycle as saturated liquid at -15°C and exits as saturated vapor at the same temperature. The mass flow rate of R-134a is 0.12 kg/s. The overall heat transfer coefficient is 1400 W/m².K. The surface area of the heat exchanger is 1.4 m². What is the rate at which heat is being exchanged between R-134a and water? Assume that the heat exchanger is perfectly insulated from outside (i.e., there is no convection or radiation with the outside/surrounding). Solution: We know, from the definition of overall heat…
Solve it quickly please
i need the answer quickly
Determine the absolute maximum shear stress of the stress state acting on the element shown in the following figure. 120 Mpa 300 Mpa 50 Мра
|Read the problem statement and the solution provided. There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. You can make the corrections directly on a copy of this provided solution, but make sure you clearly explain the corrections. Problem: Consider fully-developed flow of water through a 24-cm diameter tube. The water comes in at 20°C and exits at 40°C. The surface temperature of the tube is uniform at 60°C. The water flow has a mass flow rate of 0.24 kg/s. What is the average convection coefficient of the water flow? Solution: We have T, = 60°C, Tmi = 20°C, Tmo = 40°C, So, the bulk-mean temperature is Tm = 30°C. The appropriate properties are: u = 7.98 × 10-4 kg/ms; k = 0.615…
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Please solve it complete please don't copy paste