The figure below represents a pair of spur gear fitted on a lathe machine. A power of 6 kW at 657 rpm has to be transmitted by a motor shaft, which is input at pinion gear and its shaft rotates in The number of teeth on pinion and the gear are 29, and 72 respectively, while the module is 8 mm. Assume a pressure angle of 20°. Calculate, the torque on the shaft of the pinion and the gear.

The figure below represents a pair of spur gear fitted on a lathe machine. A power of 6 kW at 657 rpm has to be transmitted by a motor shaft, which is input at pinion gear and its shaft rotates in The number of teeth on pinion and the gear are 29, and 72 respectively, while the module is 8 mm. Assume a pressure angle of 20°. Calculate, the torque on the shaft of the pinion and the gear.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate The addendum of the gears in mm.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate The contact ratio.
A power of 120 kW is transmitted into a single reduction gear system through a pinion with 250 mm pitch circle diameter. Subsequently, the pinion which is supported in bearings on either side rotates at the speed of 650 r.p.m. If the pinion's pressure angle is 20° calculate: 2.1. the torque transmitted, 2.2. the tangential load on the pinion, 2.3. the total load due to the power transmitted.
Do it fast
2) An electric motor transmits 0.5HP at 1600RPM. A 100 tooth helical pinion having a normal pressure angle of 25° and a helix angle of 15° and a normal diametral pitch of 10 teeth/in transmits power to a 100 tooth gear. Determine the tangential, radial and axial forces on the gear tooth.
A straight tooth spur pinion has a 19 tooth pinion rotating at a speed of 1640 rpm. The driven gear will be rotating at a speed of 480 rpm. If the module of the pinion is 2,5 mm and pressure angle is 25 degree; Evaluate the outer diameter (mm) of the gear.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5°. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate: 1.4. The length of a path of a recess in mm. 1.5. The addendum of the gears in mm. 1.6. The contact ratio.
ASAP
A spur gear set is shown in Figure Q6(a). The pinion 2 rotates at 750 revolutions/minute and transmits 1.8 kW to the driven gear 3. The teeth pressure angle is 20 degrees with a module m = 2.5 mm. 30 Теeth 3 - 20 Teeth Figure Q6(a) i). Determine the forces that act on gear 3 from the pinion. ii). Draw a free-body diagram of gear 3.
A pair of spur gears with module 5 mm and a center distance of 450 mm is used for a speed reduction of 5:1 calculate the number of teeth on pinion.
A gear set consists of a full depth 20-tooth pinion driving a 40- tooth pinion. The module of the set is 2.25mm/tooth and pinion is running with 1750 rpm and transmit 25 KW. If the pressure angle used is 20° and the center distance was incorrectly made 3mm in larger, compute the contact force between teeth.
A pair of spur gear fitted on a motor shaft of lathe machine transmits the power of 5 kW at 672 rpm which is input at pinion gear and its shaft rotates in the counter-clockwise direction. The number of teeth on the pinion and the gear are 24 and 66 respectively, while the module is 8 mm. Assume a pressure angle of 200. Calculate: i) Torque on the shaft of the pinion in Nm. ii) Torque on the shaft of the gear in Nm. iii) Gear ratio iv) Center distance between shafts in mm