The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined. The open-circuit test and the short-circuit test were performed on the primary side of the transformer, and the following data were taken: Open-circuit test (on primary) Short-circuit test (on primary) Voc-8000V Vsc-489V loc-0.214A Isc-2.5A Psc-240W Poc 400W Find the impedances of the approximate equivalent circuit referred to the primary side and sketch that circuit.

If an electrical system operates at a potential higher than 600 volts, the nonmetallic conduit must be encased in at least_of concrete. A. 1 inch B. 2 inches C. 4 inches D. 6 inches

Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…

What is the unit E?

Which of the following distribution systems would you select for a medical research campus? A) Primary selective system. C) Secondary loop system. B) Distributed radial system. D) Primary and secondary loop system. Authoritative rules for electrical design and installation are contained in which of the following 7) documents? A) ASHRAE Handbook of Fundamentals. B) NFPA 101. C) NEC. The illumination from a point source 4 ft. above a surface is 100 foot-candles, and the surface is normal to the source. What will be the illumination level if the surface is tilted 45°? A) 50 foot-candles. B) 100 foot-candles. C) 71 foot-candles. Which of the following lamp types is generally the most energy efficient? A) Incandescent. C) High intensity discharge. B) LED. D) Fluorescent.

The squaring function, shifted 7 units upward.

When using an oscilloscope for testing engine management systems, what is an attenuator used for? In your answer provide an example of when an attenuator should be used. (5 - 10 words)

Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…

please tell me it is true or false . with explanation. thank you so much.

Need to help 1,2,3 questions,pls assist thanks