The equivalent circuit for a 100-MVA, 7.97kV:79.7kV transformer is shown below.mooXL(0.76 m2) (0.040 S2)wwwRLNone of the given answers635 Ω63.5 Ω7.99 kV: 79.7 kVThe resistance base quantity, Rbase, for the transformer at low voltage side, LV is about:Ο 0.635 Ω(114 S2)vooXHRH(3.75 2) (0.085 $2)

Answered: Image /qna-images/answer/0b286942-1fb1-4b74-898b-bc042681b2a9.jpg

The equivalent circuit for a 100-MVA, 7.97kV:79.7kV transformer is shown below. www RL 000 XL (0.76 m2) (0.040 S2) 7.99 kV: 79.7 kV O None of the given answers Ο 635 Ω 63.5 Ω 0.635 Ω (1142) мее mo ww XH RH (3.75 2) (0.085 (2) The resistance base quantity, Rbase, for the transformer at low voltage side, LV is about:

The equivalent circuit for a 100-MVA, 7.97kV:79.7kV transformer is shown below. www RL 000 XL (0.76 m2) (0.040 S2) 7.99 kV: 79.7 kV O None of the given answers Ο 635 Ω 63.5 Ω 0.635 Ω (1142) мее mo ww XH RH (3.75 2) (0.085 (2) The resistance base quantity, Rbase, for the transformer at low voltage side, LV is about:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.32MCQ

See similar textbooks

Similar questions

All values of a transformer are proportional to its __________________ ___________________.
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
What is the purpose of the transformer in Figure 6.25?
A IcA The voltage ratio in the following transformer equals to, Inc VAN/N1 Van/N2 Van/N1 Vab/N2
The table below shows some performance parameters of a certain power transformer. Full-load voltage regulation Full-load copper loss Load power factor 5% 0.5 Lagging Zero voltage regulation is obtained at a load power factor of: 0.9176 leading 08 leading 0.397 lagging 2% 0.703 leading
A 100 Kva transformer has 400 turns on the primary and 80 turns on the secondary. The primary and secondary resistances are 0.3 ohm and 0.01 ohm respectively , and the corresponding leakage reactances are 1.1 ohms and 0.035 ohm respectively. The supply voltage is 2200 V. The % VR and the secondary terminal voltage for full load 0.8 pf leading are: -1.44 and 330.29 V O 1.54 and 4467.7 V -1.54 and 446.77 V
In a step-down transformer ratio, which is larger the number of ratio O the number of turns O Secondary Voltage O Primary Voltage
A 400/800 ratio transformer has secondary winding resistance of 0.5 ohm. What is the total resistance in ohmsreferred to primary?
In a step-up transformer, the turn ratio is 1: 20. The resistance of 100 connected across the secondary is drawing a current of 2 A. What are the primary voltage and current respectively?
The table below shows some performance parameters of a certain power transformer. Full-load voltage regulation Full-load copper loss Load power factor 0.5 Lagging 5% The Maximum noccihle voltage regulation of the trane former is: 5.033 96 5.385 9 3 96 4.134 % 21 21
A Volt ac voltage is applied to the primary input of a transformer. A load of B ohms at the output it depends. Since the primary spiral number of the transformer is C and the secondary spiral number is C, the primary current is, Find the secondary voltage and secondary current. A= 752 B=257 C=257 Ç= 16