The driver and driven gases in a shock tube are both air at 300 K. Assume p4/p1 diaphragm is broken, an incident shock wave is propagating into the driven section and an inciden expansion wave is propagating into the driver section. If the strength of the incident shock (p2/p1) is 2.6, a. Calculate the strength of the incident expansion wave (p3/p4). = 8.006. After the b. Calculate the induced mass motion velocity behind the expansion wave.

The driver and driven gases in a shock tube are both air at 300 K. Assume p4/p1 diaphragm is broken, an incident shock wave is propagating into the driven section and an inciden expansion wave is propagating into the driver section. If the strength of the incident shock (p2/p1) is 2.6, a. Calculate the strength of the incident expansion wave (p3/p4). = 8.006. After the b. Calculate the induced mass motion velocity behind the expansion wave.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the shock tube with the given dimensions in the Figure 1 where both driver and driven gases are air. Initially the pressure ratio between driver and driven sections is p4/p1 = 9. Temperatures of the related sections are given as T1 = 288 K and T4 = 300K. Initial pressure at driven section p1 = 0.05 atm. At t=0, diaphragm located in the center of the tube is broken. For the given values: Draw the local gas velocity, pressure and temperature versus distance graphs at a given time instant t = 0.02. Mark the important points and values corresponding to that points.
A 6° half-angle wedge creates the reflected shock system inFig. If Ma3 = 2.5, find (a) Ma1 and (b) the angle α.
0/ QI diesel engine has a clearance volume is 0.00025m and bore and stroke of 152.5mm and 200mm, respectively. A charge of air at 100kPa and 20C is taken into the cylinder and compressed adiabatically y=1.4. After combustion at constant pressure the temperature is 1090°C. The expansion which follows is adiabatic. Find a- the temperature and the pressure at the end of compression b- the temperature and pressure after expansion c- the ideal thermal efficiency of the engine (591°Č,4400kPa,227°C,188kPa,0.633)
Calculate the heat rejected by 1 Kg for a perfect gas has a molecular weight of 26 and a value of Υ=1.26 , RO =8.314 , When : a-The gas is contained in a rigid vessel at 3 bar and 315o C and cooled until the pressure drop to 1.5 bar. b-The gas enters pipeline at 280o C and flow steadily to the end of the pipe where the temperature is 250o C , neglected any change in the velocity of the gas.
1. For a given pump, the diameter, the gauge pressures at the inlet and outlet are −30 × 103 P a and 200 × 103 P a, respectively. If the flow rate is 0.1 m3/s, and the power required is 25 kW, find the efficiency. The intake and discharge are at the same height. 2. The impeller of a radial-flow turbine has an outer radius of 4 f t, turning at 200 rpm. The volume flow rate is 1000 ft3/s, and it discharges in the axial direction. Neglect all losses. If the tangential component of the velocity at the inlet is 5 f t/s, find: (a) The torque exerted on the impeller. (b) The power developed by the machine.
8-A diesel engine has a clearance volume is 0.00025m and bore and stroke of 152.5mm and 200mm, respectively. A charge of air at 100kPa and 20°C is taken into the cylinder and compressed adiabatically y=1.4. After combustion at constant pressure the temperature is 1090°C. The expansion which follows is adiabatic. Find a- the temperature and the pressure at the end of compression b- the temperature and pressure after expansion e- the ideal thermal efficiency of the engine (591°C 4400kPa 227e 188kPa0 633)
A single-stage, single acting compressor has a bore of 200 mm and a stroke of 300 mm. It runs at a speed of 500 rpm. It has a clearance of 5% and a polytrophic index of 1.3. • Intake conditions are 97 kN/m² at 20°C • Delivery pressure is 550 kN/m² FAD (free air delivery) conditions 101.325 kN/m² at 15°C 5.1. Draw P-V diagram 5.2. Swept volume (0.009425 m³) 5.3.Clearance volume (0.000471 m³) 5.4. Effective swept volume (0.008106 m³) 5.5. Free air delivery (FAD) (4.053 m³) 5.6. Volumetric efficiency (80.9%) 5.7. Delivery temperature (437.5 K) 5.8. Cycle power (14 kW) 5.9. Isothermal efficiency (Neglecting Clearance) (81.3 %)
There are two double-acting pneumatic actuators, the extension of each one is executed in 5 seconds at 80 psi and recoil in 4 seconds at 30 psi, the travel of both is 12 inches, the diameter of the piston is dp = 4 "and of the rod dv = 1"a) Determine the compression ratios. The local atmospheric pressure is 79kpa = (11.5 psi)b) Determine the air consumption in cubic feet per minute of free air PCMc) Determine the average air consumption for each.d) Propose the regulation values of the pressure switch, system pressure and safety valve
+ -0.5 m- 20 kg -0.6 m- 30 kg D 0.4 m- B Calculate the critical speed in rpm (a) the Rayleigh method (b) the Dunkerley method d = 30 mm, D = 50 mm, E = 210 GPa
Calculate the reflected shock strength (p5/p2) for this question
(Use tablesS A-5-1 and A-6-1). P = 2 MPa T = 400°C V = 50 m/s Q4: (Section B) The power output of an adiabatic steam turbine is 5 MW, and the inlet and the exit conditions of Z1 = 10 m the steam are as indicated in Figure. Find: STEAM (1) The work done per unit mass of the steam flowing TURBINE Wut =5 MW through the turbine. (2) The mass flow rate of the steam. P = 15 kPa X = 90% V, = 180 m/s 22 = 6 m (Use Table A-5-1 and Table A-6-2) ********************************************** ********** *****k***********
The outer diameter of a Francis runner is 1.4 m. The flow velocity at inlet is 9.5 m/s. The absolute velocity at the exit is 7 m/s. The speed of operation is 430 rpm. The power developed is 12.25 MW, with a flow rate of 12 m3/s. Total head is 115 m. For shockless entry determine the angle of the inlet guide vane. Also find the absolute velocity at entrance, the runner blade angle at inlet and the loss of head in the unit. Assume zero whirl at exit. Also fluid the specific speed.