The discharge flowing down the pipe is 0.03 m3/s and the pressure at 2 is 20kPa. Assuming the losses in the pipe is negligible. A U-tube is connected between points 1 and 2 to determine the difference in their pressure, what would be the value of y. Liquid flowing in the pipe is water

Q: Both 150 mm square outside 300 mm 450 mm

A:

Q: kerosene, s = 0.82 A manomoter is usod to moasuro tho pressure of air shown. Solve the pressure at…

A: Let the gauge pressure at A = PA Density of mercury=13.6×103 kg/m3 Density of oil = 0.80×103…

Q: Determine the pressure at the center of the pipe from the piezometer shown. 200mm WATER 75mmØPIPE

A: Given:- a piezo meter is attached to the pipe as shosn below

Q: a sump to an overhead reservoir. The static lift is 40 m out of which 3 m is the suction lift. The…

A:

Q: In the figure, for a pressure at A of 25kPa and with losses at A which is 5 times V₁²/2g and the…

A:

Q: Oil of sp.gr. of 0.750 flows through the nozzle shown and deflects the mercury in the U-tube gage.…

A: The given data is shown below: Specific gravity=0.75Pressure at A=142 kPa

Q: -Air 45° Water dz -Mercury d2 7) Find the difference in pressure between tanks A and B if d, = 1 ft,…

A: Given data, d1= 1ft, d2=6in = 0.5ft d3= 1.5ft d4 = 8in= 0.67ft

Q: Air fl ows from a large tank, where T = 376 K and p =360 kPa, to a design condition where the…

A: Part a. Part b.

Q: Reservoir, pipe and turbine A cylindrycal tankof radiu Ra contains water. It is connected by a pipe…

A: Q = 1 L/s or 0.001 m3/s  Rb = 8 cm or 0.08 m  Rc= 4 cm or 0.04 m  h0=1.50m  L = 10m  Kinematic…

Q: QUESTION 4 The flow rate out of B is 0.03 m³/s Pipe 1 has a filter 9810 N/m³ and v=1 (106) m²/s A 50…

A:

Q: Two identical pipes (i.e. having the same lengt same diameter, and same roughness) are use to…

A:

Q: A stirrer in constructed as shown in Fig.. The dimensions are indicated in the figure. The stirrer…

A:

Q: a-) Is the flow field given in (1) incompressible? b-) Is the flow field given in (1) irrotational?…

A:

Q: A water supply tank is capable of providing 0.3 m³/s of water for fire fighting in a chemical plant.…

A:

Q: In the supply system (Q=0.89cfs) shown in the figure, the pressure required at the delivery end is…

A: Q = 0.89 cfs Diameter = 4 in = 0.333 ft Length = 1000 ft Pressure at delivery end = 65 psi Water…

Q: 6. Find the capillary rise in the tube for a mercury-air-glass interface with 0 = 130° if the tube…

A:

Q: Glycerin of SG 1.26 flows through the nozzle shown and deflects the mercury in the U-tube gage. What…

A: The values and diagram given in the question are as follows The specific gravity of glycerine=1.26…

Q: P3: Ammonia gas(A) and nitogen gas (B) are diffusing in Gunterdhs straight glass tube 2.0 ft long…

A:

Q: Find the Pressure and the total energy at the points A, .. , E 10m+ SFD Bx 100m 10m+SFD E 100m 60m…

A:

Q: D washer (2) n holes of diameter D. To reduce water consumption, a washer is installed in the shower…

A: Velocity in the pipe without reducer at section 1 and at the outlet (considering it as 2):…

Q: During a gauge field check you notice the pressure drops rapidly using the Red tube. This does not…

A: Pressure drop:- The difference in total pressure between two places on a fluid-carrying network is…

Q: For constant density flow through this round nozzle, V₁ = 1.7 m/s and V₂ = 20 m/s. The ratio of…

A:

Q: Water flows steadily downward through the pipe shown in the figure below. Viscous effects are…

A:

Q: Water is pumped from an elevated pool to a tank that is initially empty. The height from the water…

A: Given: Water is pumped from an elevated pool to a tank that is empty. The height from the water…

Q: Q2: Find the diameter of the pipe 2 in the loop shown below which contains two pipes connected in…

A: ##Calculation of diameter of Pipe 2 using hazen Williams equation

Q: 75 mm diameter nozzle is shooting out water from the pipe. Assume negligible head loss, determine…

A: Given data,  h1=1.8 m D=150 mm p=100kPa Diameter of nozzle = 75 mm   To find out the velocity at A,…

Q: Current Attempt in Progress A U-tube manometer is connected to a closed tank as shown in the figure…

A:

Q: Derive a formula for the pressure difference Pa - P in terms of the system parameters in the figure…

A:

Q: Water at 25°C is pumped into the galvanized iron pipe branch consisting of two 50-mm-diameter pipes…

A:

Q: The bar ABC in the figure below consists of an AB tube, with an outside diameter of 28 mm and a…

A:

Q: Water flows from the ground floor to the third floor in a 4-storey building through a pipe 50 mm in…

A: Discharge, Q=2 L/s Diameter of the pipe, D=50 mm Roughness coefficient, k=0.03 mm Opening diameter…

Q: na horizontal pipe, which of the following is constant?

A:

Q: Calculate the pressure in the pipe (Point A). The area of the reservoir is 100 times the area of the…

A:

Q: Home wok 2 Example (8) Steel tube shaft having length 3mm and diameter 50mm subjected to axial…

A: Schematic diagram of the given problem:

Q: The triangular valve (AB) which weighs 1500 Newtons closed at point A and is free at point B. What…

A: Length of the gate t=2sin50o=2.6108 m Depth of center of gravity from surface of water…

Q: The ratio of the momentum correction factor to the energy correction factor for a laminar flow in a…

A:

Q: Regarding the Bernoulli effect in the pump, select the correct statement. O As water flows past…

A:

Q: A pressurized tank discharges its alcohol through a square orifice (c = 0.64, cy = 0.97). If minor…

A: step 1-

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?