The directions of the X-axis are the same in the machine coordinate system and the work coordinate system.

Q: ab) What is the composite area's moment of inertia based on axis Yo?

A: we have to determine the MOI

Q: v) w) What is the distance, dsy, of shape 5's centroid from axis Yo? What is the distance, dzy, of…

A: (v) Consider the shape 5 and calculate the distance, d5y, of shape 5's  centroid from axis y0.

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: Determine the forces in members CD, CJ, and DJ. M 11' A L 8' B L 6 panels at 6' K C L J D L I E L ↑…

A: To find force in member CD,CJ,DJ

Q: can you make a sketch of the solution

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: S) t) What is the distance, d3x, of shape 3's centroid from axis Xo? What is the distance, d6x, of…

A:

Q: 1500 liters/s of ammonia gas at 100°F and pressure of 30 in.Hg has a specific heat ratio of 1.304.…

A: Given data Q=1.5 m3/sT1=100°FT2=180°Fγ=1.304 Here, Q is the flow rate and T1 is the initial…

Q: How did you get theta =45?

A: Consider following given figure of a structure.here we need to determine the angle between member DE…

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: In which of the following casting process, the melting pot is an integral part of the machine. * O…

A:

Q: Develop two possible hierarchies for assembling a model from the parts given below: Top Pins…

A: Given question: Develop two possible hierarchies for assembling a model from the parts given below:…

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: Solid pattern can be used for making Ship engine blocks Select one: O True O False

A: Solution:

Q: what happened with the 10 in the first equation?

A:

Q: I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal…

A:

Q: Can I get a more detailled explenation on how to get the numbers in the numetor in each fraction…

A:

Q: How do you solve parts a,b and c?

A:

Q: idk where you got the 4 from

A: The number of independent equations=5The number of unknowns=7To determine:Degree of freedom

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: . Convert the octal number 23228 to its decimal number equivalent, (base-8 to base-10).

A: Givenoctal number =23228

Q: I need answers to parts 7, 8, and 9, pertaining to the print provided.

A: What is the basic height of this assembly as shown in the section view?Refer the front section…

Q: A closed cylindrical vessel contains a fluid pressure of P (Mpa). The cylinder has an inside…

A: Given:Syt=340 MPad=2.5 mt=31.8 mmN=2.5

Q: A gas has an initial temperature of 25 degrees Celsius. It is cooled until its temperature reduces…

A: final temperature = 22.5o CExplanation:Approach to solving the question: Detailed explanation:…

Q: Two lenses are shown in the following figures. The one shown in figure 1 is thinner from the edges…

A: Data given-  For lens - 1 : thinner from the edges and thicker in the middle  Lens-2 : thicker from…

Q: Drive Shaft Outlet Blades Inlet Scroll Impeller

A: IMPELLER FAN A fan impeller is ordinarily joined to the turning shaft. Outer rotor engines basically…

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: I need answers for problems 7, 8, and 9 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Q: I need problems 7, 8, and 9 answered pertaining to the print attached below.

A: Cutting plane line:Cutting plane lines are represented by dotted chain line as shown in the figure.…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: Problem A solid uniform ball with mass m and diameter d is supported against a vertical frictionless…

A:

Q: 10) Define the slip angle.

A: The angle between the direction of the wheel in which it is pointing and the direction in which it…

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: Required handwritten answer, Please be sure . Don't provide wrong answer. 1)An engine produces 238…

A:

Q: Name at least two units that you use every day.

A: Most of the time in the day to day life there are many duties which have to be done daily y u. Some…

Q: What is an inflection point?

A: In solid mechanics, an inflection point is defined as a point where the curve of a physical quantity…

Q: Which of the following statement is correct in terms of degree of freedom? Select one: O Moving left…

A:

Q: Your car workshop is attended by a customer that drive a Ferrari F355 coupe for some maintenance…

A: The wrench widths given are: No Wrench Width(in) w1 1/2 w2 9/16 w3 7/8   The nut sizes…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…