The dimensions of the forklift machine are shown in the figure below. The mass of the bricks being lifted by the forklift is 2500 kg and is centered at G2. Neglect the mass of the forklift components. Determine the force in the single hydraulic cylinder CD. 800 mm 300 mm D 525 910 mm mm 55 mm

The dimensions of the forklift machine are shown in the figure below. The mass of the bricks being lifted by the forklift is 2500 kg and is centered at G2. Neglect the mass of the forklift components. Determine the force in the single hydraulic cylinder CD. 800 mm 300 mm D 525 910 mm mm 55 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.26P: The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A...

See similar textbooks

Similar questions

The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m Determine the support force on the rear tire.
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
2. The backhoe supports a 7.5 kN weight of soil in the bucket which has a center of gravity at G. Find: 0.64 m 0.25 m ● 0.26 m 0.3 m 1.68 m Force in cylinder ED (indicate if force is in tension or compression) Force in cylinder FI (indicate if force is in tension or compression) OF 0.4 m 0.1 m A -1.44 m- 17.5 kN 0.25 m D B m E 0.22 m 0.45m H O SUSIS Force in ED = Force in FI = KN (Tor C) kN (Tor C)
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal.
The homogeneous box has mass m. The magnitude of force Pis slowly increased until motion occurs. Motion could occur as slipping or tipping and you must decide which occurs first. Find the value of P which first causes motion. P 30° Ho= 0.40 B 2.2 d Answer: P = i mg
Two masses are attached to a uniform meter stick as shown in the figure below. The masses of m1 and m2 are as given and the meter stick weighs 150 g. A force F with unknown magnitude is applied on one end of the stick at an angle of 30° to balance the system. Please show the full solution.
The homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs. Motion could occur as slipping or tipping and you must decide which occurs first. Find the value of P which first causes motion. A 26° d He= 0.53 B 1.6 d Answer: P = i mg
The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal
A puck weighs 10 lb and rests on the center of the frictionless surface of the ramp supported in equilibrium by ropes AC and BC. Determine the normal force the ramp exerts on the puck as well as the tension in each of the two ropes. В A d Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 38.0 in 41.8 in 14.6 in 26.3 in 43.7 in f 8.36 in 36.9 in The normal force acting on the puck is pounds The tension in rope AC is pounds The tension in rope BC is pounds
The structure shown below is used to hold a model of the Millennium Falcon which has a mass of 380 N . W1 W2 h3 E F h2 B h1 A • Member ABCD has the following weight and dimensions: Weight of ABCD = 150 N h1= 0.8 m h2 = 1.8 m h3 = 0.1 m • Member CEF has the following weight and dimensions: Weight of CEF = 200 N w1 = 1.7 m w2 = 0.3 m • The curved member BE is massless. i. Determine the force exerted on the frame from roller D. ii. Determine the magnitude of the x and y components at each of the four pins A, B, C, and D. Part A - Part A Determine the magnitude of the force exerted on member ABCD from roller D. Enter the magnitude of the value in units of N to three significant figures. Templates Symbols Slope/Displacement Vector uado redo reset keyboard shortcuts help Dx = N Submit Request Answer
The wheels, axle, and handles of a wheelbarrow W=62N. The load chamber and its contents weigh Wl=575N. The drawing chose leave to Forsyth and different wheelbarrow designs to support the wheelbarrow and equilibrium the man's hands apply a force to the handles that is directly vertically upward. consider the rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the Man's force for both designs