Can you help with a b and c please gn7LayoutReferences Mailings Review View Help ProjectWiseThe diagram below shows an inductive circuit.14 OUnit 19 Electrical and Electronic Principles 2023-24 (1) Protected View Saved to this PC ✓OfV112V발a. Explain with the aid of diagrams, the operation of the circuit with the switch first inposition 1, and then in position 2.%b. Calculate the total current supplied to the circuit 65ms after the switch is moved toposition 1.fs*R2500c. The time taken for the voltage across the coil to reach 75% of its initial value.d. The time taken for the coil to become fully energised.e. Calculate the peak voltage at the instant the switch is moved to position 2(assuming steady state conditions have been achieved before switching).f. The potential difference across the 500 resistor after 20ms.g. Calculate the time taken for the coil current to fall to 20% of its normal running value afterthe switch is moved to position 2 (assuming steady state conditions have been achievedbefore switching).f6*f7R1100& 7PDF-XChangehpInductor470mHf88fg( 9f107fm0FocusDunne, Finlay DF00 Df12 num lkto

In the given questions we need to solve the part a, b and c.

The diagram below shows an inductive circuit. OF V1 12V R2 500 R1 100 Inductor 470mH a. Explain with the aid of diagrams, the operation of the circuit with the switch first in position 1, and then in position 2. b. Calculate the total current supplied to the circuit 65ms after the switch is moved to position 1. c. The time taken for the voltage across the coil to reach 75% of its initial value.

The diagram below shows an inductive circuit. OF V1 12V R2 500 R1 100 Inductor 470mH a. Explain with the aid of diagrams, the operation of the circuit with the switch first in position 1, and then in position 2. b. Calculate the total current supplied to the circuit 65ms after the switch is moved to position 1. c. The time taken for the voltage across the coil to reach 75% of its initial value.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

leaving a freevway. Current from the opposite side must travel further, weakening the potential on that side. This creates a potent the motor in that direction, causing the motor to spin. O Only the side where the switch is closed forms a cormplete circuit, so the motor must spin in that direction. Answer the questions and submit the photos for questions 2 -9using the circuit from STEP 2. D2 Yellow R1 50 Q R2 50 0 R3 PSB (+ 5 V 100 aLW R4 D1 100 Q Blue SW1 Sw2 Question 2 本

Electrical Engineering I need the answer as soon as possible 2y what is Cele and cladding ?
There is an RL circuit with a switch 2-volt battery, a .15 H inductor, and a 60-ohm resistor. How long after the switch is closed would there be 10 milliamps in the circuit?
How temperature effect conductivity? Explain with the help of following equation. m e'n7'
A resistor has a resistance of 20 ohms at 30 degrees Celsius and 32 ohms at 90 degrees Celsius. Find its resistance at 125 degrees Celsius. Determine also the temperature coefficient at 100 degrees Celsius. (Please Show Complete solution and write properly) (Round off the final answer to the 4th decimal if possible and box the final answer)
In the figure below you see the sketches for the front and back of an electrical circuit board. The board is cut into a trapezoidal shape and is made of plastic. On the back of the board there is conductive paint shown here in green. On the front there are some resistors and capacitors, in addition to terminals for inserting the leads from a DC power supply. The legs of the resistors and capacitors go through the holes on the board and are soldered to the conducting paint on the back side. You also have a multi-meter which you can use as an ammeter or a voltmeter. 16 v 4700 16 10 8 O- 7 3. 6. 4 O+
detailed Solution fast. R1 and R2 values are same.
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
where: R2=819ohms
5- Determine the mathematical expressions for current and voltage of capacitor following the closing of the switch. Draw the voltage and current curve. $1 R2 Hilt Vs 20 V 4KQ w R3 10KQ R1 w L C
Good day. This is Fundamentals of Electronics Circuits subject. Please do help. No need for solutions
Differential equation of the electrical system in Figure 2. HE R1 C R, Figure 2.