The density of seawater at a free surface where the pressure is 98 kPa is approximately 1030 kg/m3. Taking the bulk modulus of elasticity of seawater to be 2.34 × 109 N/m2 and expressing variation of pressure with depth z as dP = ?g dz determine the density and pressure at a depth of 2500 m. Disregard the effect of temperature.

The density of seawater at a free surface where the pressure is 98 kPa is approximately 1030 kg/m3. Taking the bulk modulus of elasticity of seawater to be 2.34 × 109 N/m2 and expressing variation of pressure with depth z as dP = ?g dz determine the density and pressure at a depth of 2500 m. Disregard the effect of temperature.

Name: The density of seawater at a free surface where the pressure is 98 kPa
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The density of seawater at a free surface where the pressure is 98 kPa is approximately 1030 kg/m3. Taking the bulk modulus of elasticity of seawater to be 2.34 × 109 N/m2 and expressing variation of pressure with depth z as dP = ?g dz determine the

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
Determine the pressure difference between points C and D. Take the specific weights to be Benzene: 8640 N/m?, Mercury:133100 N/m? Kerosene: 7885 N/m³, Water: 9790 N/m², Air: 12 N/m³. Water Benzene, Air D C 50 cm 19 cm 30 cm 18 cm 24 cm ст Mercury- Kerosine (answer) Pa
A barge floating in fresh water (ρ = 1000 kg/m3) is shaped like a hollow rectangular prism with base area A = 650 m2 and height H = 2.0 m. When empty the bottom of the barge is located H0 = 0.55 m below the surface of the water. When fully loaded with coal the bottom of the barge is located H1 = 1.8 m below the surface. Find the mass of the coal in terms of the given data.
Determine the pressure difference between points C and D. Take the specific weights to be Benzene: 8640 N/m³, Mercury:133100 N/m³ Kerosene: 7885 N/m?, Water: 9790 N/m2, Air: 12 N/m³. Water Benzene Air D 50 cm 19 cm 30 cm 24 cm $18 cm Mercury Kerosine (answer) Pa
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. d. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank.
A force, P, is applied to a piston with a mass of 15 kg and a diameter of 43 cm that rests on top of a cylinder containing water as shown. (The piston is free to move in the cylinder, but is sealed so no water can escape.) An open U-tube manometer is connected to the cylinder as shown. Determine the applied force, P in kN, if h1 = 68 mm and h = 100 mm. You can use the following data: the specific weight of water is 9.81 kN/m³ and the specific gravity of mercury is 13.546. Approximate your answer to three decimal places TU Piston Water Mercury
Q 3 :A plate ABCD hangs in water from one of its comers (as shown in the figure). Determine the total pressure on the plate and the position of the center pressure? Water Surface 10 m 5m 7 B 612 C _5 m O
A tank is filled with fluid under pressure and the pressure gauge fixed at the top indicates a pressure of 21 kPa. The curved surface of the top is quarter of a circular part of radius 2.6 m. calculate the magnitude (N) and direction (degree) of the resultant force on the curved surface. (p =950 kg/m³ for fluid) IB
Q5 A U-tube manometer similar to that shown below is used to measure the gauge pressure of water (mass density p = 1000 kg /m3). If the density of mercury is 13.6 x 103 kg /m³, what will be the gauge pressure at A if h1 = 0.45 m and D is 0.7 m above BC. Wwater Wmercury
A reservoir dam holds an 8.00-km² lake behind it. Just behind the dam, the lake is 12.0 m deep. What is the water pressure (a) at the base of the dam and (b) at a point 3.0 m down from the lake's surface? Express the answers in Pa, psi, atm, torr, mm-Hg, and bar.
The pressure difference between an oil pipe and water pipe is measured by a double-fluid manometer, as shown in the figure. For the given fluid heights and specific gravities, calculate the pressure difference AP= PB - PA. The specific gravities are 13.5 for mercury, 1.26 for glycerin, and 0.88 for oil. Take the standard density of water to be pw=1000 kg/m³. The heighth of mercury in the manometer is 25 cm. Water SG=1.0 Mercury SG= 13.5 55 cm The pressure difference is Glycerin SG=1,26 10 cm 12 cm Oil SG=0.88 kPa.
The flat surface shown is submerged vertically in water. Find the fluid force against the surface. The weight density of water is 9810 N/m3. 1 m 3 m 6 m Enter the exact answer. F = i %3D