The data given below pertain to the design of a flexible pavement. Initial trafic = 1213 cvpd Traffic growth rate = 8 percent per annum Design life = 12 years Vehicle damage factor = 2.5 Distribution factor = 1.0 The design traffic in terms of million standard axles (msa) to be catered would be

Q: a. Compute the vertical reaction of the roller support of Beam EF. b. Compute the vertical reaction…

A:

Q: b) Pretend that s for any measu made and us Task 2 A cell phone tower has been erected near your…

A: It is given that the height of tower is claimed as 50 m and height of tripod stand is 1.2 m.

Q: Q1. An I-section beam supports different loads as shown in Figure 1. Individual data of the beam…

A: Given:- w1=10 kN/mw2=9 kN/mP=7 kNF=11 kNL1=2 mL2=2 mL3=1.6 mL4=2.5 m d=178 mmbf=201 mmtf=14 mmtw=9…

Q: Problem A) A rod of mass M and length l moves across a frictionless surface with a speed v. It hits…

A:

Q: Show how to solve that V4

A:

Q: Determining quantities or afford sufficient data for the designing of works such as roads and…

A:

Q: I need to find distance between mass center and surface center points (vertically) of this…

A:

Q: Convert: 350 lb/ft3 to kN/m3 and round the result to three significant figures. A

A: Convert 350 lb/ft^3 to KN/m^3

Q: نقطة واحدة 100 Elevations in meters نقطة واحدة Value of C in the figure River Sea B 3 4 10 O 5 O O…

A: Since point C lies at the sea level hence its elevation is considered as zero. Because the mean sea…

Q: Solid Mechanics Set up the appropriate equation that is used to solve for the moment of inertia…

A:

Q: I. In your own words, what is more important-precision or accuracy? State a real-life scenario where…

A: Accuracy is the degree to which a value is true to itself.

Q: Which of the following is always the same for a uniformly sized conduit conduiť O pressure head…

A: Pressure head is same for uniformly sized conduit. If cross section is uniform then pressure head at…

Q: The following are the ordinates of 3-hr UH. Derive the ordinates of a 12-hr UH and plot the same.…

A: Let solve using S -curve

Q: Oil of density 917 kg/m3 and dynamic viscosity 0.29 Pa.s flows in a pipe of diameter 15 cm at a…

A:

Q: Problem In which surveying, shape of earth is taken into consideration? Technolagy Druen by i O…

A: Geodic surveying shape of earth is taken into consideration in Geodic surveying

Q: 1. A balloon rises from the ground with a constant acceleration of 4 ft per sec?. Five seconds…

A: The values given in the question are as follows: Constant acceleration of balloon(a)=4 ft/sec2…

Q: Civil Engineering The snowmobile is traveling at 10 m/s when it leaves th embankment at A. Suppose…

A: Given v=10msθ=36°Range is R=vx×tR=vcos36·t

Q: W1 A L 1 L2 L3 20 + [A* D] KN W1 = 30 + [ B * c ] kN /m W 2 = + [c* D] 15 KN /m し1= 1 + A m 5 + D M…

A:

Q: What is the Shear Load on segment A-B? * O - 27 kips -25 kips -21 kips O -19 kips What is the Shear…

A: Given a beam with symmetric loading conditions  Required: To find shear load on segment A-B…

Q: Determine velocity KE-2300 J m-23 kg

A:

Q: 6. Discussion: 1. Is there a difference between the values of the nozzle velocity (vn) and the jet…

A:

Q: Calculate the resultant force caused by the water acting on the parabolic arch dam. water levels are…

A: solution ; since ther is symmetry in y direction, so resultant force in y direction will be zero.…

Q: Why water balance in hydrology is significance in water calculation?

A: 1.The water balance have significant purposes to describe the various ways in which the water supply…

Q: what are real life problems and solution of infiltraion ?

A:

Q: Convert 100 min/cm^3 to m^3/h

A:

Q: . The arch of a masonry bridge is a semi-ellipse whose span is 95 ft and whose height in the center…

A:

Q: A student organization is building bird houses to help some of the endangered birds around the Rio…

A: - Surface area of four side walls of bird house, SAsw = 2(12*6)+2(8*6) = 144+96 = 240 square inch  -…

Q: The actual velocity in the contracted section of a jet of liquid flowing from a 50mm diameter…

A:

Q: Does the function, =Ur cos0+cose represent possible irrotational flow?

A:

Q: What is the dependency of head losses across pipe fittings upon the velocity head?

A: The head loss across a pipe fitting is directly proportional to the velocity head's square. This is…

Q: 10. Which of the following is correct? a) pathlines are concerned with a number of particles at the…

A: Which of the following is correct?a) pathlines are concerned with a number of particles at the same…

Q: Draw a network for a house construction project. The sequence of activities with their predecessors…

A:

Q: A balloon rises from the ground with a constant acceleration of 4 ft per e seconds later, a stone is…

A: Detailed Solution

Q: Physics La magnitud de la fuerza F= 218 N, se aplica en el punto A y su línea de acción pasa por B.…

A:

Q: A shunt pipe placed horizontally is shown on the right. The average velocity of section 1 is V1 =…

A:

Q: (a) The hydrological behavior of a region depends on its climate, topography and geology. Based on…

A: Effect of climate: The climate is a very important factor in hydrology. The rate of evaporation is…

Q: PART I. CRITICAL PATH METHOD From the given Activities and their Durations below, create a Critical…

A: The critical path method (CPM) is a technique where you identify tasks that are necessary for…

Q: Find mass of car K.E=2300 J velocity=15 m/s

A: ASKED: To determine the mass of the car.   Given, Kinetic energy (KE) = 2300 J Velocity of the car…

Design of pavements

Pavement is a structure that is made up of different layers such as sub-base course layer, base course layer, binder course, and a surface course formed with different materials such as gravel, above the subgrade soil constructed to act as a path or carriageway enabling the movement of vehicles. The surface of the pavement should possess characteristics such as adequate friction, light reflection, and drainage. The pavements are classified based on structural design into rigid pavements, flexible pavements, composite pavements, and unpaved pavements. The process of determining a suitable pavement type, its constituent layers, and its thickness is called pavement design.