3.The copper shaft is subjected to axial loads shouwn below. Determine thedisplacement of end A with respect to end D. The diameters of segments aredAB=75mm, dBC=50mm and dcp=25mm. Use Cu modulus of elasticity of 126 GPa. 250 mm--1875 mm--1500 mm10 kN5 kN30 kNC 15 kND.AB 10 kN

Displacement: - It is defined as the distance moved by any section with respect to its Centre of…

Answered: The copper shaft is subjected to axial…

The copper shaft is subjected to axial loads shown below. Determine the displacement of end A with respect to end D. The diameters of segments are

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² Pr B C D 500 mm -250 250 mm 350 mm- ANSWER: KN, PBC = PCD = KN KN, PAB= (express it in whole number) A
The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Ebr 100 GPa. Figure P P -10 mm -20 mm 1 of 1 Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Submit Part B Obr = Submit 0 Value If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Provide Feedback A Request Answer Value Units Request Answer Units ?
Determine the length of tension anchorage required for the 36 mm diameter plain mild steel reinforcing bars in the canrilever of figuer below. The charactersitic material strengths are feu-30N/mm² and fy=250KN. The ultimate anchorage bond stress. Stress, fou-1.5N/mm² Anchorage length R25 bars
In the assembly of the bronze tube and steel bolt, the pitch of the threads is p = 1/32 in.; the cross-sectional area of the bronze tube is 1.5 in? and of steel bolt is 4 in?. the nut is turned until there is a compressive stress of 4,000 psi in the bronze tube. Find the stresses (psi) if the nut is given one additional turn. How many turns of the nut will reduce these stresses to zero? Use Epr = 12 x 106 psi and E = 29 x 10° psi. L= 40 in.
The two wooden boards are connected by a 0.9 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D = 3.0 in. and d = 1.0 in. The nut is tightened to cause a tensile stress of 14000 psi in the bolt. Determine the bearing stress between the washer and the wood. Answer: Ob = Bolt 1575 D - Washer - Washer Nut psi
The two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm. Knowing that beam is subjected to V 5000 N, and that the moduli of elasticity for steel and wood are 200 and 40 GPa, respectively. Determine: (a) Shearing stress in each bolt; and (b) shearing stress at the mid- height of the upper steel plate. 150 mm 12 mm 250 mm 12 mm Solution:-
The assembly consists of a bronze tube and a threaded steel bolt. The pitch of the thread is 1/32 in. (one turn of the nut advances it 1/32 in.). The cross-sectional areas are 1.5 in? for the tube and 0.75 in? for the bolt. The nut is turned until there is a compressive stress of 4000 psi in the tube. Find the stresses in the bolt and the tube if the nut is given one additional turn. Use E = 12 x 10° psi for bronze and E = 29 x 10° psi for steel. Bronze tube 40 in.-
The two wooden boards are connected by a 0.7 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D = 2.4 in. and d = 0.8 in. The nut is tightened to cause a tensile stress of 12000 psi in the bolt. Determine the bearing stress between the washer and the wood. Answer: Ob = i Bolt D Washer psi - Washer Nut
42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >
Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² P P₂ B C D +250 -350 mm 500 mm A -250 mm- ANSWER: KN, PBC = PCD = KN KN, PAB = (express it in whole number)
A plate with width of 300mm and thickness of 20mm is to be connected between two plates 12mm thick with same width by 4-25mm diameter rivets a shown. The rivet holes have a diameter 2mm larger than the rivet diameter. The plate is A36 steel with yield strength Fy=248 Mpa and Fu-400MPa. The rivets have nominal shear stress capacity of 165MPa. O 803 O 1490 • Determine maximum load (P1) that can be applied without exceeding design tensile stress in plates (consider yielding and rupture of plates ONLY) in KN O 1180 O 1340 ο ο ο ο ο P3 O 1968 O 590 O 670 O 893 O 707 OO 150 O 1180 P1 P2
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPa, f, = 280 MPa and the net tensile strain is greater than 0.005, then the maximum steel ratio equal............ (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None