The controlling force curve of a spring controlled governor is a straight line. The weight of each governor ball is 40 N and extreme radii of rotation are 10 cm and 17.5 cm. If the values of the controlling force at above radli are 205 N and 400 N respectively and friction of mechanism is equivalent to 2.5 N at each ball. Find The extreme equilibrium speeds of the governor. (1) The equilibrium speed and coefficienct of insensitiveness at a radius of 15 cm

The controlling force curve of a spring controlled governor is a straight line. The weight of each governor ball is 40 N and extreme radii of rotation are 10 cm and 17.5 cm. If the values of the controlling force at above radli are 205 N and 400 N respectively and friction of mechanism is equivalent to 2.5 N at each ball. Find The extreme equilibrium speeds of the governor. (1) The equilibrium speed and coefficienct of insensitiveness at a radius of 15 cm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
Find the smallest distance d for which the hook will remain at rest when acted on by the force P. Neglect the weight of the hook, and assume that the vertical wall is frictionless.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
A photograph shows two U.S. Coast Guard icebreakers in an ice field and a simple model for an ice breaking operation. The coefficients of static and kinetic friction for contact between the ship's bow and ice are 0.08 and 0.054, respectively, and the ship produces a thrust of 106 forces between the ship's hull and water except for the thrust. Ib. Assume the ship makes contact with the ice only on its bow, and neglect all 1170 T17° Determine the normal and friction forces acting on each side of the ship's bow as it moves through the ice field with constant velocity. The normal force is x 106 lb. The friction force is x 104 Ib.
In a Hartnell governor, the lengths of the ball and the sleeve arms are equal. The extreme radil of rotation of the balls are 60 mm and 80 mm and the corresponding speeds are 160 r.p.m and 175 r.p.m. Each ball has a mass of 2 kg. Find the spring stiffness and the initial compression of the central spring.
Ql: A box weighing 100 N is at rest on a horizontal floor. The coefficient of the static friction F sin 6 between the box and the floor is 0.4. What is the NA F cos 0 smallest force exerted eastward and upward at an angle of 30° with the horizontal that can start the box in motion?
the system blocks shown below is in equilibrium, the weight of block A is 10 kN and for block B is 35 kN. The coefficient of friction between A and surface is 0.2 and between two block A and B is 0.15. Answer :the following P=40KN B The value of friction force between the * block B and it's surface is 25 kN 35 kN 15 kN Non above-mentioned * The system is in Equilibrium Impending to motion Kinematic
B r P F A UBC Engineering Your team is prototyping a simple braking system for your model car. The 3.4 kg wheel with a radius of r = rad 0.15 m is rotating at w = 18 - .A servo motor can apply a variable force F, which in its first two seconds of operation is equal to F = 10t N and afterwards is equivalent to a constant force of F = 20 N . If the coefficient of kinetic friction between the braking arm and the wheel is μ= 0.2, determine the time needed for the wheel to come to a full stop. The point of contact P between the wheel and the arm is a distance r = -0.2 + 0.26 ĵ m from point A. The force of the servo motor is applied at exactly half of the horizontal distance to A from the point of contact. Assume the wheel can be treated as a disk and that the braking arm is massless. t =
7The total sleeve movement in a Hartnell governor is 3 cm. The mass of rotating balls is 1.5 kg each. At the mid position of the sleeve arm, which is 6.5 cm long, is horizontal. The ball arm has a length of 7.5 cm. At the mid position of the sleeve, the balls rotate at a radius of 10.5 cm. Due to the mal adjustment of spring, the equilibrium speed of governor at top position is 415 rpm and In lowest position it is 430 rpm. Determine (1) Stiffness and initial compression of spring. (ii) Required initial compression in spring which gives equilibrium speed at the topmost position which is rpm more than the lowest position neglect bliquity.m = 1.5 kg
3- (WORK AND ENRGY) The block M in Fig (a) weighs 500N and has a downward velocity of 5 m/s at the instant the force P-1 kN is applied. The coefficient of friction between the arm AB and the rotating body is 0,4. The rotating body weighs 800 N and has a centroidal radius of gyration of 50 cm. Find the distance the weight travels before coming to rest. 30cm. 60cm 30cm