The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case:

The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case:

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.27P

See similar textbooks

Similar questions

The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case:
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: PV and TS diagrams of the cycle showing ideal and actual process lines Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.___________________________
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Combined work (KW) . Ans.____________________________ Combined steam rate in kg/KW-hr. Ans.___________________________ Actual heat rate( KJ/KW-hr). Ans.____________________________
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Ideal turbine work (KW). Ans.____________________________ Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Pump work in KW. Ans.___________________________
Steam is generated at 4.10 Mpa and 440°C and condensation occurs at 0.105 MPa a. For a Rankine engine operating between these limits, computethe thermal efficiency and the heat rate b. Considering that a Rankine cycle occurs between same limits, determine QA, QR, Wnet and eth c. What mass flow rate is required for a net output of 30 000 kW Don't answer the given problem, just give me the schematic diagram and t-s diagram of the given problem
Exampie Air conditioning unit uses Freon R-22 for conditioned office at 25 C. The evaporating temperature is 17 C and the condensing temperature is 47 C. The compressor is reciprocating and single acting with number of cylinders of 4, volumetric efficiency of 0.9, number of revolution is 900 rpm cylinder dimensions of L/D is 1.25. If the compressor power is 3 kW and mechanical efficiency of 0.9, estimate the followings: the refrigerant mass flow rate in kg/min, refrigeration capacity in TR, cylinder dimensions, condenser heat load, coefficient of performance and relative efficiency. and
5. Sketch a Rankine eycle on T-s diagram and derive the thermal efficiency for a rankine eycle from its 4 steps. Show on T-S plot and discuss what is the effect of a. Increasing superheat b. decreasing condenser pressure c. Adding friction at pump and turbine
3- A reaction turbine is supplied with steam at (60 bar, 600 C°). The condenser pressure is (0.07 bar). If the reheat factor can be assumed to be (1.04) and the stage efficiency is constant throughout at (80%). Calculate the steam flow required in (ton/hr) for a diagram power of (25 MW). (Ans. 75.6 ton/hr) The ctoam ntion at full load for a 12 MWV) turbine ic (1 S 6 ton /brl At balf lead the
A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec. pls dont skip anything show all solution including conversion of units
(a) What would be the necessary bore and stroke of a single acting four- cylinder, 350 rpm ammonia compressor working on simple saturation cycle between 35°C condenser and -15°C evaporator temperatures and developing 15 tons refrigeration. Given for the compressor: Ratio of stroke to bore = 1 Volumetric efficiency = 0.7 (b) If the index of compression is 1.15, find the error introduced in calculat- ing the work of compression by assuming the process to be isentropic. Also, find the heat rejected to the compressor-jacket cooling water.
Air is cooled and dehumidified at constant pressure as shown in the figure below. Heat removed by the cooling coil is 130kW. Find air mass flow rate, air volumetric flow rate, condensation flow rate and sketch al states in a psychrometric diagram . Use AirH20 as the working fluid PLEASE NOTE: T2 has a typo, it should be 16.7 degrees Centigrade, not 16.7 degrees Fahrenheit, and all temperatures should be in Centigrade