The concrete floor of a hand regulator is level with the channel bed and is 13 m long. The depth of upstream and downstream cutoff wall is 2.5 m and 2.0 m. The upstream F.S.L. is 1.5 m above the floor level, then the value of exit gradient is [Use Khosla's theory] A 0.17 B 0.12 C 0.20 D 0.22

Q: 35 aw the projections of this shape 25 20 20 A

A: GIVEN:   TO FIND: Draw the projection of the given shape.

Q: When are the singularity functions used?

A: Solution-  We can observe that the shear and bending moment expressions get increasingly complicated…

Q: Give other methods of determining the horizontal distance between two points.

A:

Q: What are the characteristics of ordinal level measurement scale variables?

A: Data provided :  Ordinal level measurement scale variables    To determine : The characteristics of…

Q: Please fill in the blank for this question please! A *blank* call identifies a corner or boundary,…

A: A _________call identifies a corner or boundary, usually as some object that constitutes the…

Q: continue dimension and baseline dimension?

A:

Q: ONS B.S. H.I. F.S. LF.S. ELEVATIONS -a 1.24 234.51m 1.11 3.40 4.6 2.8 3.6 2.4 3.21 2.46 1.2 3.2 2.8…

A: Given profile levelling HI = elevation +   BS elevation = HI - FS or IFS given elevation of BM a =…

Q: Draw the 3 Principal Views of the object (given unit in mm, convert it to cm) 51 35 15 25 53 73 20…

A: 3D view of the object is provided. We have to draw three principal views of the object.  Three…

Q: Indicate briefly, using words or sketches, how geosynthetics have been used to prevent groundwater…

A: Applications of Geosynthetics that are used to prevent ground water contamination:

Q: For any engineering example discuss with drawing the Bathtub Curve

A: The bath tub curve is generally used in reliability engineering.   This curve signifies the…

Q: geomorfologie

A: Note: As nothing is mentioned in this problem so, we are assuming that we have to only define this…

Q: Give the coordinates for the following autocad drawing

A: The points are named as below

Q: what is the difference between 42 square meter and 42 meter square

A: It is needed to differenciate between 42 square meter and 42 meter square.

Q: Describe about the Taylor Charts.

A: Taylor's stability chart are used for determining the stability of slope of cohesive homogeneous…

Q: 12. To make a stretch to an object, the procedure is: left click stretch icon, select the object,…

A:

Q: Give the vector in cartesian coordinates that extends from B(4, 20degrees, 10degrees) to W(7,…

A: The given data is shown below: B=4,20 degrees, 10 degreesW=7,120 degrees, 75 degrees

Q: a. On the equator: b. Golden, Colorado: C. Barrow, Alaska: 0° latitude 39°44'N latitude, 105°12'W…

A:

Q: Break the shaded area into the five different areas shown. Find the area and the x- and…

A:

Q: SANITARY PLANNING LAYOUT " F. SYMBOLS AND LEGENDS

A:

Q: Level surface, Bubble line, Horizontal line, Level line, Line of collimation, Bench mark, Change…

A:

Q: With the aid of an illustration, describe two methods by which areas bounded by irregular lines can…

A: Areas bounded  by irregular lines can be found by using midoridnate rule , trapezoidal method ,…

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A: The force of shear is a sensitive force on the surface. It's said to be the bending moment the…

Q: What of the following about the scale is/are false ?

A: The scale represents the ratio between the measurement drawn in a plan to the actual measurements.

Q: Q24. Draw the plan, section and elevation of the given line diagram. W BED KITCHEN 2500x2500 D…

A:

Q: Convert 36° 19' to decimal degree form.

A: Given data: θ=36∘19'

Q: What are the advantages and disadvantages of the bar chart ?

A: The advantages of Bar chart are as follows: Bar charts are pretty easy to interpret, and there's a…

Q: What is the actual area enclosed by the following figure, using the scale of 1"=40'? 4" Area = _ft²…

A: Converting given dimensions to actual dimensions on field

Q: Determine the centroidal coordinates (x, y,z) of the volume.

A: Question is based on the section . Dimension of section are given in the question . Centroidal…

Q: what are aerial cameras?

A: Answer:- Aerial Camera:- It is a camera which is designed for use in aircraft and containing a…

Q: What is the elevation of point C?

A:

Q: Define Relative Density.

A: Relative density or specific gravity:

Q: What are velocity charts?

A: The Velocity Chart displays the value amount delivered in each sprint so as to forecast the work…

Q: bulation gives elevations of points over the  area of a 30m x 40m city lot. The elevations were…

A: Given:- area=30mx 40m To find:- Plotting contours

Q: 15 2.

A: Top view will be:

Q: Locate the centroid of the given area below. Semi-Circle Square

A:

Q: 4. Complete the accompanying set of profile notes and perform the arithmetic check. Provide a sketch…

A: The levelling terms and formula. BS = Back sight The first measurement taken in a survey. It is the…

Q: Which is the most common type of BIM model where a specification constrains what can be modeled?…

A: This question is related to the Building design from Civil Engineering.

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.