The column shown in Figure B-1(a), not drawn to scale, carries a horizontal load W applied in the plane of the web; the cross-section of the column is shown in Figure B-1 (b). If the maximum value of direct stress in the column is limited to +-155 N/mm2 calculate the maximum allowable value of W.

Q: Motor (12) solid column with a diameter of 50 mm subject to the moments shown in the figure. Find…

A:

Q: Find the residual forces acting in a truss with members AC=1000N (T), EG=520N (T), and FH= 1200N (C)…

A: Given AC=1000 N (Tensile)          EG= 520 N (Tensile)          FH =1200 N (Compression)

Q: All the tension/compression members of the frame structure shown in the figure are pin-jointed and…

A:

Q: Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm…

A: stress is defined as the force per unit area.

Q: The assembly in Figure consists of a light rigid bar AB, pinned at O, that is attached to the ste…

A: Given             Deflection = 5 mm          Area of steel = 250 mm2 Area of aluminum = 300 mm2 Find…

Q: 3 cables with same diameter are used to hold the plate. Calculate the tensile loads in all cables if…

A: Givencables with load as  shown below

Q: A steel bar with a diameter of 100 mm is rigidly attached to the wall and carries the loads shown in…

A: Given: The diameter of shaft, d = 100 mm = 0.1 m The torque acting on the shaft, T = 8 kN.m The load…

Q: A single-piece bicycle crank is shown below under the following load: the rider pedals forward with…

A:

Q: P MATHalino.com -12 in- -6 in 6 in F 3 in A 13 in B 12 in- 2 in 6 in Cross- Section

A: The value of forces are

Q: From the figure shown, the tube has an outer diameter of 80 mm and an inner diameter of 70 mm.  The…

A:

Q: A metal bar is made out of A-36 steel and has a diameter d 20mm with the end at A fixed to the wall.…

A: Step 1: Step 2: Step 3: solution is given above Step 4:

Q: 10 kN В B y 6 m

A:

Q: ember BED is supported using steel rods AB, CD, and EF as shown below. E-20 If a force P is applied…

A: GivenL1=425mmL2=320mmP=8kNAAB=310mm2ACD=310mm2AEF=420mm2E=200GPa

Q: The given system below, consisting of a rigid horizontal bar ABC and supported by three vertical…

A: Given data: -  The diameter of rod B is DB = 26 mm. The length of rod B is LB = 4400 mm. The…

Q: Flat steel A is welded to the wall as shown in the figure. The profile of the flat steel is…

A: Based on the image you sent, I can't access the specific data points to solve for the median grain…

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a - 2 ft • b = 4 ft C = 1 ft then,…

A:

Q: The structure shown in Fig 4-4.17 consists of two simple trusses joined by bars Be, CF and DG. Find…

A:

Q: The round bar in the figure is made of steel (E-207 GPa). The load F has a magnitude of 100 N. You…

A: Young modulus of the material,(E)=207 GPa. Applied force (F)=100 N. Diameter of the shaft,(d)=20 mm.…

Q: Consider the frame shown in Fig 4. A 100N load is suspended around a fixed drum with radius 2 m…

A: Draw the free-body diagram of the frame.

Q: Calculate the internal force (positive if tensile, negative if compresive) in rod (2). Use a FBD…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: Given data: P=9 kipsQ=4 kipsR=18 kipsS=21 kipsσ1=19 ksiσ2=24 ksiσ3=12 ksi Need to determine the…

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A:

Q: Problem #3. The figure below are cables ( circular section) supporting a 36 kN. Find the axial…

A:

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…

A: Given : w = 2.25 in t = 0.375 in P = 4,800 lb d = 0.775 in   The average bearing stress produced in…

Q: 50 KN is applied in the center of the block on the top. The area of the cross section at AB and CD…

A:

Q: The space truss above is supported by ball-and-socket joint at points A, B, and E. A single force F…

A:

Q: Torsional moments affect the rods as shown in the figure. a- Draw the torque diagram on the rod.…

A: Torque is the turning effort caused due to the force. The torque diagram represents the loading…

Q: Q4\ A filleted. plate of thickness t supports an axial load P (Figure below). Determine the diameter…

A:

Q: A homogeneous bar with a cross-sectional area of 400 mm² is attached to rigid supports. It carries…

A:

Q: Т2 KN KN MPa MPA MPa MPa

A: Given data as per questiondimensions of  steel plate = 2.5 x 1.5 x 0.08 m weight of the steel plate=…

Q: in. diameter bolt connects the marine propeller to a boat's 1-1 in. driveshaft (see the figure…

A: The area of the bolt is-

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.