The channel is made of wood and has a downward slope of 0.0020. Determine the depth of flow y that will produce the maximum volumetric flow using the least amount of wood when it is flowing full of water, that is, when y = h. What is this volumetric flow? Take n = 0.012. %3D y 2 m answer: y = 1 m, Qmax = 4.70 m² /s %3D

The channel is made of wood and has a downward slope of 0.0020. Determine the depth of flow y that will produce the maximum volumetric flow using the least amount of wood when it is flowing full of water, that is, when y = h. What is this volumetric flow? Take n = 0.012. %3D y 2 m answer: y = 1 m, Qmax = 4.70 m² /s %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a) find the weight of concrete dam if it has a depth of eleven meters into the page. Where does the weight act (centroid)? b) if the water level is less than 4m, what are the horizontal and vertical load intensity diagrams and the equivalent point load (in cartesian form in terms of "h") for each? c) repeat b if the water level is greater than 4m.
Please do 2.10 all parts
6. A block of wood (sg = 0.78) floats in water with 600 cm³ above the water surface. What is the total volume of the wood in cm³? A. 2727.3 C. 2989.4 B. 2653.8 D. 3214.4 7. The Froude number of flow in a rectangular channel is 0.85. If the depth of flow is 1.3 m, the critical depth is: A. 0.95 m C. 1.22 m B. 1.08 m D. 1.17 m
Need sap. Please be clear and detailed with your solution. Box your fina answer.
Compute the average end volume Sta 25+00 2,875 2,502 3,336 2,356 Sta 25+75 107' A₁ 125' (in cubic yards - yd³) using the figure below: 111' A2 131' elev = 102.9' elev = 95.4' elev = 102.5 elev = 94.8'
Draw the qualitative EGL and HGL for the water transfer system below. Water T = 10-C p= -88.29 KPa gage Elevation 10 m Elevation = 6 m 40 cm diameter D = 30 cm Elevation = 2 m
Please answer hand writing
A rectangular flume is 15 cm wide and 8 cm high. The freeboard is 25% of the flume height. What is the hydraulic radius in cm?
Q/shows a hycreaulic structur thut was built on opm channel . The residunl head at point f calculated by using Lon's theory is equal to 1.25m. Thi suk o + and G2.5. bydraulic gradient is equal to : 50 Lon's VIs WIL h, = 125 - +4, G.2.5 12465 15m 12m 15m
Re = 2* 106 e/d = 0.04 Find f? 0.1 f 0.03- 0.008 Laminar flow 64 f-1 (Re) Critical zone Moody's Diagram Transition Zone 2000 1-1 (R. e/D) Smooth pipe f-f(R.) R. Fully Turbulent zone f-f(e/D) e 2×106 e Q Re-2×10 c/D-0.04 f=? Ans = 0.03 -0.05 0.03 e/D 0.004 108 0.00001 Activate V Son
Dont give wrong answer will dislike for sure
Water at 60 degrees Fahrenheit have a density of 62.36 Ib/ft.^3 and dynamic viscosity of 7.536 x 10^-4 Ib/ft-s) is flowing steadily in a 2-inch diameter horizontal pipe made of stainless steel at a rate of 0.2 ft^3/s. Use f = 0.0200. Determine %3D the head loss in terms of inches over a 200-feet long section of the pipe. A) 327.60 В 27.30 C 376.05 D None of the above