For the casting of the part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design,all the molding stages and finally, draw the mold in the most suitable form for casting and name all the mold elements by showing them on the figure(Note: The hole shown in the figure is a full hole. .) Tam Delik

thế časting part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design 11 the molding stages and finally, draw the mold in the most suitable form for casting and name all the mold elements by showing them on the figure Note: The hole shown in the figure is a full hole. .)

thế časting part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design 11 the molding stages and finally, draw the mold in the most suitable form for casting and name all the mold elements by showing them on the figure Note: The hole shown in the figure is a full hole. .)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the sand casting of the part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and and finally draw the most suitable form mold for casting, and name all the mold elements by showing them on the figure (Note: The hole shown in the figure, full hole.) please draw the shapes more clearly and remember to draw each step.Thank you in advance
For the casting of the part, whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and finally the mold in the most suitable form for casting, and name all the mold elements by showing them on the figure (Note: The hole shown in the figure, full hole.)
For the casting of the part whose perspective pictures are given below, take into account the section surface (model design), (core design if necessary), all molding stages and finally (the mold in the most suitable form for casting) and name all mold elements by showing them on the figure (Note: The hole seen in the figure is a full hole.)
For casting the part, whose perspective pictures are given below, into sand mold,model design, core design if necessary, all molding stages andFinally, draw the mold in the most suitable form for casting and shape all the mold elements.Name it by showing on it (Note: The hole shown in the figure is a full hole.) !!! Please draw the desired shapes !!
A sand casting mold is shown. All bottom and side plates have a uniform thickness of 1". The bottom plate is 10" by 5". The side plates have a width of 5" and height of 4". The outside diameter of the tube is 3" and inside diameter is 2 ". The tube height is 4". The inside hole of the tube extends to the end of the bottom plate. Ignore the plate that is connected to the side of the tube. Ignore all the curved corners. min Design a cylindrical riser with the height of 4" for this mold. The mold constant is 25 in?
Q3) Select the proper part number with the matching letter statement in the following table: ( following the solved example. ) Part number Matching Statement Statement 1-g Example A frame made of metal or wood or plastic, in a 1 Shrinkage cavity which the mold is formed. Slight taper given to a pattern to allow 2 Flask or molding box 3 Sprue b drawing from the sand. The top half of a horizontally parted mold A passageway through which the molten 4 Chaplets d metal enters the mold cavity. Draft e to support the cores inside the mold cavity The passage through which the molten metal flows from the pouring basin, and reaches the mold cavity Solidification shrinkage that restricts the amount of molten metal available in the last 6 Cope 7 Gate region to freeze
QUESTION 14 Pieces thicker than 5.45mm are considered sheet. O True O False QUESTION 15 In sand casting, natural sands are less economical than synthetic sands. O True O False QUESTION 16 Typical sheet-metal thicknesses are between 0.15 mm and 7 mm. O True False
2. State one casting defect associated with excess moisture content in the mould. 3. State two reasons why moisture is required in moulding sand 4. Knust steel foundry shop is to formulate a moulding sand containing sand, clay and water only, in the sand to clay fraction of and respectively. If the sand obtained is dry but the clay is moist with moisture content of 15%, how much water should be added to formulate 850g moulding sand?
QUESTIONS 1- Describe with net sketch: a. Pattern b. Riser c. Runners d. Core 2- Compare between open mold and closed mold. 3-Explain the main Procedures of Sand Casting. 4 - What are the important properties which are essential in good molding sand? Explain in details. 5- Mention advantages and disadvantages of casting. 6- Describe types of sand mold. 7- What are the common binders of sand mold and cores? 8- Describe Desirable Mold Properties. 9- Explain two types of patterns and two pattern allowances 10- Describe with sketches shell process casting (i) Composition of sand mixture (ii) Steps in molding (iii) Advantages (iv) Limitations and (v) Applications 11- Explain with Sketch the construction and operation of a hot chamber die casting machine. 12- Compare between hot chamber die casting and hot chamber die casting. 13- What is meant of investment casting? What are the main materials used for making the investment pattern. 14- Describe various kinds of patterns in use. 15- Why…
QUESTION 18 Rearrange the following steps which illustrate the sand-casting process in brief. Heat treatment of casting product is sometimes required to improve metallurgical properties Pour the molten metal into sand mold Cavity Break up the mold to remove casting A Allow time for metal to solidify + Clean and inspect casting product Make the Pattern and Core box * Separate gating and riser system + Prepare sand casting mold for pouring QUESTION 19 Which of the following is mostly used for holding bored part of the job? Mandrels Steadies Collet Face plate
You are designing a mold to cast the solid part shown in the figure below from pure copper. If the runner diameter is 1 in and the molten copper velocity in the runner is 0.5 in/s. If the Chvorinov Constant is 50 S/in². Calculate the number of casts we can fill and solidify on a single sand mold in 1 shift = 8 hours duration? Part Dimensions in inches A = 5 B=3 C=3 D=3 E=2 E F= 2
QUESTION 1 a) Explain what is the basic difference between expendable and permanent molds used in metal casting? Briefly also describe what are the primary advantage and disadvantage of each these two types of molds? (CO1, PO1, C2) b) Describe the steps involved in making the sand mold and the casting, including what steps that may be needed to improve the casting after it is hardened and removed? (C01, PO1, C2) c) One of Open Mold processes for shaping fibre reinforced plastics (FRP) is Hand Lay Up. List the five (5) steps involved in the Hand Lay Up method? (CO2, PO1, C2`