The cantilever beam in the figure is a 3 m long h229 wide flange profile. the isolated load at the free end is 2000 kg and the beam also supports a uniform load of 600 kg/m, including its own weight. Determine the deflection at a point 2.5 m from the embedment wall and the maximum stress in the beam. take e = 2.1 x 106 kg/ cm2 the =8050cm4. P p kg'unidad longitud L

Q: Determine the location of Neutral Axis, in mm, from the top of the section.

A:

Q: For the given system: rods 1 (at both ends), d = 0.625 in and E = 15,000 ksi; rod 2, d = 0.375 in an...

A:

Q: Que : A hollow circular shaft of Inner Radius 6 cm and Outer Radius 10 cm and length 200 cm is subje...

A: Given data, Length of the shaft=L = 200cm  Angle of twist at free end= 0.01rad   Maximum shear angl...

Q: PROBLEM 2: A support block is acted upon by two forces as shown. Knowing that the coefficients of fr...

A:

Q: Determine the resultant (in newton) of the forces acting on the pin as shown in the figure if the fo...

A: Given data,  F1 = 1 kN θ1 = 24° F2 = 8 kN θ2 = 49° To find out the resultant of forces acting on the...

Q: Check the adequacy of the beam with respect to moment. Use tables of quantities (coefficient of resi...

A: The values and diagram given in the question are as follows Span of the beam(L)=20 ft Service live l...

Q: 6 KNIM 45 KN/m 3m 3.6m

A:

Q: 3. When the measured angle in vertical plane using a total station (=zenith angle) is 16 24'45", wha...

A: Given data: Zenith angle = 16∘24'45"

Q: 2. Dozer Production Calculation How long will it take for a track-type dozer w/straight blade to mov...

A: A dozer is a motorized machine equipped with a metal blade in front used to push and move materials....

Q: PROBLEM 2: A support block is acted upon by two forces as shown. Knowing that the coefficients of fr...

A:

Q: A solid steel rod with (0.1em) diameter is fixed to the vertical surface at point (4), before it is ...

A: To determine the reactions at support A and B'.   Given, Diameter of the steel rod (say d) = 0.1 cm ...

Q: A beam segment with its internal shear forces at sections A and B is shown along with a sketch of th...

A:

Q: For a colony of 10000 persons having sewage flow rate of 200 1/capita/day, BOD of applied sewage is ...

A:

Q: 3 ksi 2. For the state of stress shown in the figure, determine normal and shearing stresses on the ...

A:

Q: A,- 150 mm E,- 200 GPa 3 m A,- ? 400 mm (1) E,- 70 GPa 1.8 m (2) 0.7 m 0.3 m 1.8 m A,= 400 mm'(3) E,...

A: Using equilibrium calculate the tension in cable. Then using formula the extension can be calculated...

Q: 3Km 40KN pinsed suppart pinned support 10 KN &m calculate the axial forces of the members

A:

Q: Q-3: Determine the discharge of a distributary at the tail end from the following data: Gross Comman...

A:

Q: A man exerts a force Fon the handle of the stationary wheelbarrow at A. The weight of the wheelbarro...

A: Find force F that must be applied at A

Q: A steel tube is rigidly attached between an aluminum rod and a bronze rod as shown. The maximum P va...

A:

Q: Structural Theory

A:

Q: Create a design mix using the ACI DESIGN MIX PROCEDURE with the following parameters: Non-Air Ent...

A: Reference : ACI 318 1. Find W/c ratio: Table : Relationship between water to cementitious material r...

Q: A seepage flow condition is shown in the figure. The saturated unit weight of the soil Yet = 18 kN/m...

A: Given data,  Ysat = 18 kN/m. Unit weight of water, Yw = 9.81 kN/m, To find out the vertical stress a...

Q: A plate of 150 mm width and 20 mm thick is welded to another plate by fillet weld as shown in the fi...

A:

Q: In your own words, explain What is meant with Forensic Photography?

A:

Q: Question 2: Joints A, B, C, D, and E are frictionless pins. F and G are rough surface contacts. (a) ...

A:

Q: The beam is supported by a pin at B and a roller at D. The applied loads shown in the figure have ma...

A:

Q: A prybar is used to remove a nail as shown. Determine the moment of the 265-N force about the point ...

A:

Q: Complete the table and show complete computations. Draw the aggregate gradation chart.

A:

Q: Problem 3. $40. Design a rectangular beam to carry the load show, in addition to its self-weight. As...

A: Given data f'c = 4000 psi fy = 60000 psi Unit weight of concrete = 150 pcf Dead Load WD = 3 k/ft Liv...

Q: A torsion member is fabricated fror concentric thin tubes. At the ends, the are welded to rigid disc...

A: Given data: Inner radius = r outer radius = 2r shear stress in outer tube = τ  

Q: Problem 8. Solve all reactions (Ax, Ay, Cx, and Cy) for this structure. Note: force is transferred o...

A: To find horizontal and vertical component of reaction at A and C

Q: A two-lane minor road with a +5% approach grade intersects with a four-lane undivided road. Determin...

A: step 1-

Q: Find deflection at C and D. Using Moment- 22,500 lb Area Method 3000 lb/ft LE B C D 4 ft 12 ft 6 ft ...

A: We have to determine the value of deflection at C and D using moment area method as per the given da...

Q: 8. Both ends of a beam of length L is embedded at two walls and a varying load w(x) per unit length ...

A: In designing, deflection is how much a piece of a primary component is uprooted under a heap (since ...

Q: Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section made from a T-...

A:

Q: A simple circular curve has a radius of 300 m and 60° deflection angle. Compute the following: a. it...

A: Given, Radius of the curve= R= 300m, Deflection angle= ∆= 60°         Note :- as per our company gui...

Q: kN The magnitude of stresses of the soil element represented by the figure below are o, = 250; m kN ...

A:

Q: The results shown in the following table were obtained at the pea a series of CD TXC with a constant...

A: Step 1: σ3 = 70, 140 σ1 = σ3 + σd= 265+70, 494+140 = 335, 634 Horizontal axis is labeled normal stre...

Q: A saturated compressible clay layer of thickness h is sandwiched between two sand layers, as shown i...

A: Given-Thickness of clay layer=hpore water pressure, u=25 kPavertical stress,σ=150 kPaadditional vert...

Q: section made from a T-Section and a Channel (C-Section) fastened together by 16mmØ bolts, equally sp...

A:

Q: Identify which of the following is true?     a. In simple curve, if you are in PI, the stationing of...

A: To Determine Which of the given sentence about horizontal curves are correct.

Q: Which of the following most nearly gives the ratio of the volume below the liquid surface to the tot...

A: Given:- specific gravity of object =0.60 specific gravity of liquid=0.80 To find:- (a) ratio of the ...

Q: Find the conjugate of z. If z (5 + i) - 3+4i i Simpli fy, 1+? 2

A:

Q: TOS1 Part 1- Shear and Moment Diagram • Using the shear and moment diagram, determine the location o...

A:

Q: From the system of forces shown in Figure. Each square is 1 ft. on a side. a. Determine the resultan...

A:

Q: Find moment at O, given the figure below. 50 N 2 m 5 m O 70 N-m clockwise

A: Find moment at O, given the figure below.

Q: Item 2 Determine o". Determine the equivalent state of stress on an element if it is oriented 30° Ex...

A: Given -  To find - 

Q: Plot to scale; elevation head, pressure head and total head. Also, determine graphically the flow di...

A: Introduction :  Seepage is the flow of water under gravitational forces in a permeable medium. Flow ...

Q: Can you help me with this please show the clear complete solution and fbd Given: W =  600 lb Tensi...

A: W=600lb  To find tension in cable AB,AC,AD

Q: The data shown were taken from a certain part of road to be constructed Base for fill = 7 m sideslop...

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.