The cables AC and BC supports a load W with L= 20m a. If x1 = 7m and d= 2m what is the normal stress at both cables when loaded with W=60kN with cables’ cross sectional area is 20mm2

Q: In the following structure, consider the following data: The connection at D is double and has a…

A:

Q: In the steel structure shown, a 6-mm-diameter pin is used at C and 10- mm-diameter pins are used at…

A: Determine Vertical Displacement of point A in mm

Q: 3 decimal places PLEASE   1. Calculate the shear stress in the pin in MPa. 2. Calculate the…

A: Given data in question  Load Dimensions  To find out  Shear stress Bearing stress

Q: Problem 3 in the steel structure shown, a 6-mm-diamter pin is used at D and 10-mm-diameter pins are…

A:

Q: 1.0 m 3.3 m A simple pin-connected truss is loaded and supported as shown. All members of the truss…

A:

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A: GIVEN DATA:-⇒a = 4.25 ft⇒b = 5.10 ft⇒A = 2.1 in2⇒σ = 35 ksi

Q: In the structure shown, in diameter pins are used at A, B&D The ultimate shearing stress for the pin…

A: Diameter -  ϕpin = 13in   Ultimate shearing stress -  At point D -  σD = 6ksi  At AB -  σAB = 10 ksi

Q: In the steel structure shown (see Figure Q1), a 6-mm-diameter pin is used at B and C and

A: According to given data

Q: Calculate the average shear stress in MPa of the pins B and C on the frame shown in the figure. Note…

A:

Q: In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B.…

A: Given:Diameter of pin at C is 6mmDiameter of pin at B is 10 mmRequired:Largest P applied

Q: Exercises: Determine the normal stress in each member of the truss structures. 1. All joints are…

A: Given a=b=2cm

Q: The member shown has a rectangular cross section, determine the state of stress that loading…

A:

Q: If a force with a magnitude of P applied to point E and in turn it causes the rigid lever to rotate…

A: Find average normal stress in wires

Q: A laminated plastic beam of square cross section is built up by gluing together three strips, each…

A:

Q: D CED Front view 18 mm 6 mm B B Side view 160 mm 120 mm A Top view In the steel structure shown, a…

A:

Q: 20MPA a In Figure , according to the stress condition of a stack of I-section beam. (30Mpa is the…

A: Principal stress=σx+σy2±σx-σy22+ζ2=40+-202±40-(-20)22+302=10±42.42 MpaThus σp1=52.42Mpa and…

Q: The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are…

A: Given data: Shear stress τ = 70 MPa Bearing stress σ = 140 MPa Diameter of rivet d = 19 mm   For the…

Q: COMPUTE THE SHEARING STRESS IN THE PIN AT B FOR THE MEMBER SUPPORTED AS SHOWN IN THE FIGURE. THE PIN…

A:

Q: Q1: Find the normal stresses at sections A-A, B-B, C-C, and, D-D for the body as shown in figure…

A:

Q: ABD rigid bar with 40mm diameter BC bar at point B, It is supported from point A with a 30 mm…

A:

Q: The pin-connected rigid rods AB and BC are inclined at 0 the force P is applied, 0 becomes 32°.…

A:

Q: Q4 - For the given beam and cross section, at point B on section A-A (mid-span), determine the…

A:

Q: 1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used…

A:

Q: What is the Maximum Shear Stress, t, on the centric axially loaded member shown? The cross-sectional…

A: Given data : Axial load (P)=40 kipsCross sectional area (A)=2 in2

Q: Knowing that a force P of magnitude 1000 N is applied to the pedal shown, determine (a) the diameter…

A:

Q: 1) If the radius of cables AB and CD are 5mm and modulus of elasticity is 20GPA, calculate the…

A: It is asked to find normal stress and normal strain in cable AB & CD.

Q: 1. Draw the axial force diagram of the rod. The diameter d=10mm, F=5kN. E=210GPa. Determine the…

A:

Q: In the following structure, consider the following data: The connection at D is double and has a…

A:

Q: The maximum tension in the INwer link of a Porter governor is 580 N and the maximum stress in the…

A: Given data in question  Stress Load To find out  Diameter

Q: In the system in the figure, a) Since oy=500 MPa and the factor of safety is n=3, Find the cross-…

A:

Q: A roof truss and the detail of the connection at joint B are shown in the figure. Angle sections…

A: For the given roof truss:

Q: The truss shown consists of wooden members. Knowing that each member has a 100 x 100 mm. square…

A:

Q: the AC rod suspended. The cross section of the AC rod is 15 x 8 mm2. 1.6 tons of force is applied to…

A:

Q: QI: Find the normal stresses at sections A-A, B-B, C-C, and, D-D for the body as shown in figure…

A:

Q: The plate shown in the figure is fastened to the fix member by three 10 mm diameter rivets. Compute…

A: Given data The plate is fastened to the fix member by three 10 mm diameter rivets

Q: A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is…

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.