The cable AB carries a tension of 530 N. Determine the moment about O (positive if counterclockwise, negative if clockwise) of this tension as applied to point A of the slender bar. B 400 mm 690 mm 21 Answer: Mo= i N.m
Q: D 10 cm 30° M C B 20 cm Quest The allowable tension and compression stresses are given as: gtension…
A:
Q: 12mm dia 18mm dia. P=12 kN 2 m. 12mm dial 2. Three steel cable jointly support a load of 12kN. The…
A:
Q: Locate the center of gravity of the figure shown, knowing that it is made of thin brass rods of…
A:
Q: a G 6 mm b
A: Radius R=6mmlocation of center of gravity G(x,y)=(0,0)
Q: Ag what force is holding the solid together?
A:
Q: Assume a person's mass is 54.0 kg and each of her shoes has an area of 195 cm². F on her feet if her…
A:
Q: How is the bulk modulus at equilibrium distance Beg related to the cohesive energy of the crystal u…
A: The bulk modulus (B) of the material is given using the following expression. But the pressure P…
Q: The upper end of the bar is leaned against a nonvertical wall. Determine the minimum value of the…
A: Let the weight of the bar be where .The horizontal force, The vertical force, The moment A,
Q: = 250 MPa and the
A: Let the bending movement equation, MI=σyM=σy×I
Q: A crate weighs 660 lb and is hung by three ropes attached to a steel ring at A such that the top…
A: Given, A crate supported by three ropes. The weight of crate is 660lb
Q: If the beam attached to a hinge is 4 meters long and weighs 600 Newtons, and the sign weighs 400…
A:
Q: The homogeneous wire ABCD is bent as shown and is attach to a hinge at C. Determine the length L…
A: this question is about to measure center of gravity of wire for equilibrium.
Q: A cylindrical beam has a diameter of 1.8 m and a shear modulus of 1.0 x 1010 N/m2 projects out a…
A: Given, diameter of a cylinder beam is d=1.8m so the radius of the cylinder beam is r=0.9m shear…
Q: The correct solution will get a helpful rating for sure Provide Answer in Handwritten format.
A: Step 1: Step 2: Step 3: Step 4:
Q: Two cylinders of cross-scctional area A = 10 m are fitted smoothly together as shown in the Figure,…
A:
Q: P-2. A steel shaft 2 m long that has a diameter of 90mm. is subjected to a torque of 10 KN-m. Use G…
A:
Q: The beam is subjected to the distributed load and the couple shown. If M is slowly increased…
A:
Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…
A:
Q: What torque
A: Given dataL=2.76m=2760mmInner diameter, c=3.313×10−2m=33.13mmSimilarly outer diameter b=76.63mmAngle…
Q: 3. A flat steel bar 150 mm wide by 50 mm thick has axial loads applied at points A, B, C and D as…
A: Solution: The free-body diagram of the forces of the bar in section BC is shown in the figure.
Q: Two aluminum plates, each having a width of b = 5.6 in. and a thickness of t = 0.725 in., are welded…
A:
Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…
A:
Q: Calculate the x-, y-, and z-coordinates of the mass center of the bracket formed from the steel…
A: Centre of mass of system.
Q: a. AU 0 and AU0.
A:
Q: The homogeneous 40-kg basr ABC is held by a horizontal rope attached to end C. Neglecting friction,…
A: Given : mass m = 40 kg ω = mg = 40×9.81 = 392.4 N
Q: Determine the magnitude of F if the particle is in equilibrium given that θ = 26° and P = 134 .
A:
Q: Don't use chatgpt. Only Handwritten solutions are allowed
A:
Q: 2- The square plate is deformed into the shape shown by the dashed line. Determine the average…
A:
Q: In rolling, if the maximum draft is 13 mm, & the coefficient of friction is 0.3, thus the minimum…
A: As per bartleby guideline for more than one question asked only first is to be answered please…
Q: A steel wire of length 1.40 m and diameter 1.00 mm is joined to an aluminum wire of identical…
A: We are given the mass of object. We can thus find the force acting on wire. We then find the stress…
Q: - A rigid member CBD is supported by a flexible cable AB as shown below. If a force applied to the…
A: Take point C as origin and vertical as y axis. Initial coordinate of point B =0,300 Initial…
Q: Determine the x-y, and z-coordinates of the mass center of the body constructed of three pieces of…
A:
Q: For the plane trusses supported by the spring at node 1 determine the nodal displacements and the…
A:
Q: Steel construction beams, with an industry designation of "W12 x 25," have a weight of 25 pounds per…
A: Disclaimer: “Since you have asked multiple question, we will solve the first question for you. If…
Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…
A:
Q: A uniform steel rod has mass 0.300 kgkg and length 40.0 cmcm and is horizontal. A uniform sphere…
A: Take x-axis along the horizontal of the rod with 0.900 kg sphere on left and 0.680 kg sphere on…
Q: A bending moment of M=15kNm is applied to the beam in the figure with the notches below and a hole…
A: σ=bending stressM=bending momenty=distance from the neutral axisI=moment of inertia M=10kNm W=140mm…
Q: 4. A single axial load of P = 60 kN is attached at the end C of the brass rod ABC. Knowing that E =…
A:
Q: 75 kN Composite A-36 steel bar shown made from two segments AB and BD. Area A= 600 mm² and App=1200…
A: Write the given values of this problem. AAB=600 mm2ABD=1200 mm2
Step by step
Solved in 2 steps with 1 images