The bottom area of a rectangular plate is 40cmX 60cm, as shown in the figure 3.7. The mass of the plate is Skg, it evenly declines along with the horizontal plane into 30° cant at the velocity 1.0 m/s. The oil thickness between the plate and the cant is Imm. How much is the dynamic viscosity coefficient of the oil? 30 Figure 3.7

The bottom area of a rectangular plate is 40cmX 60cm, as shown in the figure 3.7. The mass of the plate is Skg, it evenly declines along with the horizontal plane into 30° cant at the velocity 1.0 m/s. The oil thickness between the plate and the cant is Imm. How much is the dynamic viscosity coefficient of the oil? 30 Figure 3.7

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The planar AB cover with a width b = 2 m perpendicular to the plane of the figure is articulated at point B F = 7620 Newton force is applied from point A. Since the weight of the lid is W = 5600 N, find the water depth h for the equilibrium state.Note: Specific mass of water is ρsu = 1000 kg / m3. (figure in image) #fluidmechanics
26. An open-top cylindrical tank 1 meter in diameter is 2.80 m tall. The tank floats in water with a draft of 2.30 meters. Unit weight of lead is 110 kN/m^3 a) What is the weight of tank in KiloNewtons? b) How much lead (in KiloNewtons) must be fastened to the outside bottom of the tank in order make it completely submerged in water? c) How much lead (in KiloNewtons) must be placed inside the tank in order make it completely submerged in water? (Ans. 17.72kN; 4.23kN ; 3.85kN)
Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The coefficient of static friction for the contact surfaces is 0.35. (i) (ii) Determine the mass value of block B when the impending motion of block A is down the plane. Determine the mass value of block B when the impending motion of block A is up the plane. 20⁰ А μs=0.35 Figure Q2 B
Calculate the friction drag on a plate (length 0.8 m and width 0.3 m) up to the point at which the boundary layer flow changes from laminar to turbulent. The water is flowing from both sides of the plate at a rate of 3 m/s. (u = 9 × 104 Pa-s ; critical Reynolds number Rec = 5 x 105)
The surface tension of mercury at 60°C is 0.47N/m. What capillary height in mm will occur in this fluid whe in contact with a glass tube of radius 0.3mm? Use 130° for mercury. O 11.5mm fall O 11.5mm rise O 15.1mm fall O 15.1mm rise
A cube contracts in volume by 0.05% when acted upon by normal uniform pressure of 2x 106 N/m? on all sides. The bulk modulus of its material is (а) 400 MPа (4000 MPa (d) 40000 MPa (b) 40 MPа
Given the bulk modulus of water B-2.1x1o° Pa= 2.1 GPa, What increase in pressure needs to be applied to the surfaces of a cube of water 1 m on a side to reduce its volume by 4%? O a 0.0600 GPa Ob. None. O c.0840 GPa O d. 0.0700 GPa O e 0.1050 GPa
A line was found out to be 2865.35 m long when measured with a 30-m tape under a steady pull of 6.5 kg at a mean temperature of 30 degC. Determine the correct length of the line if the tape used is of standard length at 20 degC under a pull of 5.5 kg. Assume that the cross-sectional area of the tape is 0.025 cm², elastic modulus of tape is 2.10 x 106 kg/cm? and coefficient of linear expansion of steel is 11.6 x 106 per degC.
A spherical pressured tank of radius 1.5m is being designed by a civil engineer to be a storage of natural gas from the Malampaya gas field. The gas it will contain is subject to a change in temperature of 295 °C with an internal pressure of 20 MPa. The final design of the tank gives a 9 mm wall thickness with a Poisson's ratio of 0.28. Use a = 11.7x10 /°C and E = 200 GPa. %3D a. Determine the tangential/longitudinal stress. b. Change in radius.
A liquid has an absolute viscosity of 2.231025 Ib-s/ft?. It weighs 45 Ib/ft. What is its kinematic viscosity?
A liquid has an absolute viscosity of 2.431023 N-s/m?. It weighs 7.853103 N/m?. What is its kinematic viscosity?