The blades on the radial-flow pump shown in (Figure 1) rotate atw = 200 rad/s. The blades are 2 in. wide.Figure8 in.1 of 1 >Part AIf the discharge is 240 ft³/min, determine the ideal pump head.Express your answer using three significant figures.hpump = 1.52SubmitIVE ΑΣΦ | | | vecProvide FeedbackPrevious Answers Request AnswerX Incorrect; Try Again; 4 attempts remaining?ft

Answered: Image /qna-images/answer/46a2f737-0c11-40c9-9673-ac27dc2d2fbf.jpg

Answered: The blades on the radial-flow pump…

Engineering

Mechanical Engineering

The blades on the radial-flow pump shown in (Figure 1) rotate at w = 200 rad/s. The blades are 2 in. wide.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump draws 20 L/s of water from reservoir A to reservoir B. Assuming f = 0.013 for all pipes, compute the horsepower delivered by the pump. Pump elevation is at datum.Data as follows: Reservoir A to pump. L= 500 m, D = 200 mm, EL. = 15 m Pump to Reservoir B L= 1200 m, D = 150 mm, EL. = 60 m
Fluid Mechanic Water, as seen in the figure above, is a 25° angle contractor in a piping system. With an elbow, it is directed downward in the installation with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. The flow is frictionless and the effects of gravity are neglected. a-)Effective pressure at point 2 b-) Elbow in place Calculate the x and y components of the force required to hold and the resultant force (pwater =1000 kg/m3, g = 9.81 m/s2)
Given: Two (2) identical pumps connected in parallel has the following data: Suction Pressure = 315 KPA Discharge Pressure = 220mmHg Suction Pipe Dia = 390mm Discharge pipe Dia = 405mm Velocity of Water = 6.0 m/s Solve: Total Head, Pump1 & 2 individual head and if Pump 2 is 9.5% less than Pump 1 and Q₁ = Total Flow Rate
Figure Q6 shows the head (H) vs flow rate (Q) curves of a centrifugal pump at a certain condition where the pump operating flow rate is Q1 as shown in Figure Q6. However, the required flow rate is Q2. With the help of sketches or graphs, discuss possible solutions that can be applied to produce the required flow rate Q2.
Water at 5°C is to be pumped from the river to the bottom of a water tower. The pump is 5 m above the river (dimension "a" on the diagram below) and is supplied by a 6.00 inch schedule 40 pipe. The tank is 19.5 m above the pump (dimension "b" on the diagram below) and is supplied by a 4 inch schedule 40 pipe. The water level in the tank is 4.3 m above the inlet (dimension "c" on the diagram below). The pump delivers 0.021 m/s. Losses are estimated to be 1.2 m between the river and the pump, and 4.2 m between the pump and the tank. Discharge line Suction line Pump River a) Calculate the losses in the suction line in kPa, based on the given head loss in m. kPa b) Calculate velocity in the suction line in m/s. m/s c) What is the pressure at the inlet to the pump in kPa? kPa
A turbine has the following data: inlet radius = 2.2 m outlet radius = 1.5 m blade width at inlet = 0.8 m blade width at outlet = 2.1 m inlet blade angle = 66º outlet blade angle =18.5ºN = 100 rpm Q = 85 m3/s Calculate the angle at the inlet by which the wicket gates should turn the flow from radial. Round off your final answer to two decimal places.
In the hydroelectric power plant whose cross-section is given, the flow rate of Q=33.045 m^3/sec is transmitted to the power plant through a D=1.6 meter diameter penstock. Ignoring friction losses; a) Find the internal pipe pressure at point 2 ( at the below ). b) Find the resultant force (F) and its direction (O) that the water exerts on the fixation mass. c) Calculate the electrical power generated in the plant. (Pwater= 1 ton/m^3, Ywater= 9.81 kN/m^3, g=9.81m/s^2, Beta= 45 degree
in designing a ram pump, make computations where the Source Elevation = 50 meters. Target User Elevation = 85 meters. Target output = 230 Liters/min
A centrifugal pump is used to pump a liquid with the properties given below. Liquid is pumped from a storage tank at 95 kPa (a) to a discharge tank at 300 kPa (a). The system configuration is given in the table below. Table 1: system configuration Suction Discharge 4 50 Length (m) Diameter (m) 0.07 0.055 12 90° bends (L/D-35) 5 T piece (L/D=7) Gate valve (L/D-35) 1 1 1 2 Static height (m) 25 Liquid density = 1100 kg.m³ Viscosity = 1.5 x 10-³ Pa.s Vapour pressure of the liquid = 25 kPa (a) Material of construction of pipe is commercial steel, ε = 000045 m Table 2: Pump data 0 10 20 30 40 Flowrate (m³.hr¹) Head (m) 55 56 51 36 6 NPSH (m) 0 2 6 11 19 22 3.1. Graphically determine the optimal operating point of the pump in the above system using the pump data in Table 2. 3.2. Determine the NPSH of the system and determine whether the pump will cavitate when used in the above system.
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
Using the performance curve of pump A given in Example VIc.3.2 (41.5” and 710 rpm) and find: a) total dynamic head of a similar pump (pump B), at peak efficiency, having a diameter of 35 inches. Assume that both pumps A and B are operating at the same speed. b) pump head if pump B is now operating at 1170 rpm. [Ans.: a) H = 192 ft and b) H = 521.5 ft].
As shown in the figure, the water is directed downward in the installation with a 25 ° angle narrowing elbow in a piping system with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. Where the flow is frictionless and gravitational effects are neglected, a) Find the effective pressure at point 2. b) Calculate the x and y components of the force needed to hold the elbow in place and the resultant force. (psu =1000 kg/m3, g = 9.81 m/s2).