The blade on a typical table saw rotates at 3100 revolutions per minute. Calculate the linear velocity in miles per hour of one of the teeth at the edge of the 10 inch diameter blade.

Q: The length of a workpiece is 5.25 in. is tapered in the lathe. If the shafting has .035 taper per…

A: GIVEN DATA- LENGTH OF WORKPIECE = 5.25in. TAPER PER FOOT = 0.035 WE HAVE TO FIND AMOUNT OF OFFSET

Q: 45) Find the RPM for turning a 1 1/4 inch shaft on a lathe with the material having a cutting speed…

A:

Q: How is spindle aligmment done in a milling machine?

A: By spinning a cutting tool (cutter) and sliding it into the work item, a milling machine removes…

Q: 9. Write the formula for calculating spindle speed in revolution per minute for milling machine,…

A: GIVEN DATA-  A MILLING OPERATION QUESTION ASKED  WE HAVE TO WRITE SPINDLE SPEED RELATION

Q: Q24. For the below figure please write its part program. The depth of the cut is 0.25 inches…

A:

Q: 1. What type of milling machine can be used to make the groove in the shaft? 2. The diameter of the…

A: 1. Grooves, elongated slots and break-throughs are produced or made for the purpose of receiving…

Q: A vertical boring mill is used to bore the inside diameter of a large batch of tube-shaped parts.…

A: Given, Bore diameter = D = 28 in Length of the bore = L = 14 in Current cutting speed = v = 200…

Q: The time required to saw a rectangular piece of stainless steel plate 3.5 meters long and 2.25…

A:

Q: In machining operation, if velocity doubled then the tool life reduced to 1/16 th of initial value…

A: Givenvelocity get double of initial velocitytool life reduced to 116of initial value

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting…

A: Given data: The cutting speed of the tool is v=22 mmin The feed of the tool is f=0.2 mmrev The depth…

Q: A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm…

A:

Q: ф20 O 25 $10 25 10 45

A: Machining time is given by, T=LfNwhere, L=length of operationf= feed in mm/revN=rpmGiven:V=60…

Q: Find the spindle speed in rpm, if the slotting operation is performed by 16mm end mill with a…

A: Manufacturing processes: The various processes that are involved in converting raw material into a…

Q: Calculate the spindle speed (rpm) for turning operation when the cutting speed is 186.00 m/min and…

A: Find the spindle speed  Cutting speed = 186 m/sec External diameter = 38.50 mm

Q: A two-spindle drill cuts two holes at the same time, one 1/2 inch and one 3/4 inch. The workpiece is…

A:

Q: Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A:

Q: spur gear angle for the bevel gear at D is 18° and the bevel angle is 45°. Note that the shaft is…

A: Given : The radius is The pressure angle  for the spur gear is The pressure angle of bevel gear at D…

Q: D d a° L1 SI. Parameter in Dimension in No: Drawing mm 1 d 35 2 L1 28 Cutting speed (Cs) in m/…

A:

Q: A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm…

A: Note: As per our company guidelines we are supposed to answer only the first 3 sub-parts. Kindly…

Q: A 48 in diameter diamond saw blade is mounted on a pulley driven steel shaft, requiring a blade…

A: Given 48 in diameter diamond saw Angular velocity = 150 ft/sec Power = 125 hp Rotation = 1200 rpm…

Q: The face milling cutter of D = 200 mm used to cut a block which is 200 mm = H, 1=480 mm, if f- 0.7…

A: Machine time is the ratio of length divided by cutting speed. Here,  Length = length of block +…

Q: Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given               D = 22 mm = 0.022 m  Speed, N = 260 rpm

Q: Choose the right answer - In turning, the cutting force that increases by decreasing depth of cut…

A: In turning operation the cutting force is the resultant of tangential force, feed force, and radial…

Q: A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine…

A:

Q: In crank and slotted lever quick return mechanism, the crank length is (100 +X )mm and the distance…

A: consider reg. no. of the student is 11912081 then X=81 crank length= 100 +X = 100 + 81 =181 mm…

Q: Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a…

A: Given data Mill diameter (d) = 14 mm = 14 x 10-3 m Cutting speed (v) = 16 m/min

Q: Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given data  spindle speed (N) = 260 rpm end mill dia (d) = 22 mm = 0.022 m    To determine  Cutting…

Q: Quest-5 b, The distance between two parallel shafts connected by Oldham's coupling is 25 mm. The…

A: The distance between two parallel shafts connected by Oldham's coupling r = 25 mm.The driving shaft…

Q: To draw a line, select the line tool and tl Draw the line y=(1)/(2)x+6

A: Giveny=12x+6

Q: QUESTION 1 Calculate the spindie speed in RPM of a lathe turning a 96 milimeter diameter material…

A:

Q: Program the motion of cutting tool from point 1 to point 2 according scheme below, in absolute…

A: Write the absolute programming for CNC lathe, using the radius programming.

Q: Turning operations on work piece reduces following dimensions,

A: Lathe machine: Lathe machine has to operates various operations such as cutting, facing, knurling…

Q: 1 A gear is turning per Speed with radius at 17/11 $ What a point second. at is on rad th t

A:

Q: 3. It is required to machine a slot with length 100 mm, width 15 mm, and depth 4 mm. Calculate the…

A: Given: The length of machine slot, L = 100 mm The width of machine slot, b = 15 mm The depth of…

Q: In a shaper machine, the crank rotates at constant speed of 130 r.p.m. The angle travelled by the…

A: Given that :           A shaper machine           Crank rotating at speed (N) = 130 rpm…

Q: agine two ordinary gears of different diameters meshed together, with the larger being the driver.…

A: Given:Z1=108 ω1=5.80 rad/sZ2=20

Q: In a lathe machine the cutting tool has a diameter of 1.6 cm is subjected to a cutting force of 250…

A:

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.