The bent rod ABDE is supported by ball-and- socket joints at A and E and by the cable DF. If a 133-lb load is applied at C as shown, %3! determine the tension in the cable. z = 13 in. Write numerical value only and in 2 decimal places. 8 in. 7 in. F 9 in. A P В 11 in. x E 14 in. 16 in. 12

Q: 51 degree. Determine A force F = 160 N is applied to a two-bar truss as shown and 0 = the value of…

A:

Q: For the beam and loading shown, consider section n-n and determine the shearing stress at a) point…

A: Given data : We are asked to determine the shearing stress at  A ) Point a  B ) Point B

Q: Une énd and supported on linear elastic springs (both having a rigid beam Is ninged #ness of 'K') at…

A:

Q: 35 - In the plane truss system, the loading status of which is evident in the figure, the support…

A: Analysis of truss can be done by method of joint or method of section. The forces acting internally…

Q: s. Determine the tension in each wire.

A:

Q: What is the maximum absolute shear in the following beam? Use L = 21, a = 2, b = 4, P₁ =1, P₂ = 4,…

A:

Q: 180.0 40.601 7. One grid line = 1 foot. 2. Draw the arrows and label the reaction forces. Label the…

A:

Q: I. Method of Members 1. The portable table shown is to support a load P = 1.5 kN at a variable…

A: P (load) = 1.5KN L = 1.5m

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A:

Q: The frame is subjected to the load of 15 kN which acts on member ABD at D. Determine the required…

A:

Q: What is the maximum absolute shear in the following beam? Use L = 22, a = 3, b = 3, P₁=2, P2=5, and…

A:

Q: Problem 2: For the shown Truss Without Calculations: • Determine all zero-force members on the shown…

A: Given data:

Q: Determine the forces in members AC and BD. The forces are positive if in tension, negative if in…

A:

Q: QUESTION 6. D 5A SA

A:

Q: The negative moment in the short cantilever shown in Figure 13.21 is resisted by the steel bars in…

A: At the support, anchorage for development must be achieved on both ends. within the top of the beam…

Q: For

A:

Q: SOLVE FOR EACH FORCE MEMBER OF THE GIVEN TRUSS. (USE METHOD OF JOINTS) E P₁= 30N P₂=15N P₁₂ F -3 m B…

A:

Q: Determine the forces in members EH and El of the double Fink truss (positive if in tension, negative…

A: The member forces EH and EI can be found using method of sections.

Q: P1 3 m P2- 3 m B A -3 m P3 2 m C D

A: The structure with reactions can be shown below For equilibrium of statics (i) ∑MD =0 (cw +ve, ccw…

Q: Knowing that the tension i n cable AC is TAC = 345 N, determine the z-component of TAC. Round off…

A: Given Data: The tension in cable AC is, TAC=345 N   To Determine: The z-component of TAC.

Q: Determine all the member forces of the given truss in kN. Indicate as negative if compression and no…

A: Determine the force in each members of the truss. Let's solve using method of joints.

Q: Determine the bending moment 2.39 m to the right of point A for the beam shown belowif P = 1006 N, T…

A: Draw the FBD and using equilibrium equations the value of any internal force can be calculated.

Q: a hinge at G method of sections to compute the Force in bars and by a voller at C. Use the BC, and…

A:

Q: * Ignore Internal Strain Energy due to axial load and shear. A (pinned) 15 ff 2 k/ff V C (hinge) V…

A:

Q: 6 kN A 2.4 m B 2.4 m C 2.4 m D 2 m E 5 m F G H.

A:

Q: 1a/Assume the support at A and B or D are pins

A: The objective of the question is to understand the forces acting on a structure and how they are…

Q: (a) By observation, determine zero force members of the bridge shown in Figure 2.1 (No calculation…

A: I

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

A:

Q: The electric power transmission tower supports two wires that apply 18 kN vertical forces, and the…

A: Member DE is zero force member.

Q: The rigid pipe is supported by a pin at A and an A-36 guy wire BD (E = 29 000 ksi). If the end C is…

A:

Q: The Warren truss loaded as shown is supported by a roller at c and a hinge at G. By the method of…

A:

Q: QUESTION 4) In the frame system in figure, the diameter of pin at joint B is d. The allowable shear…

A:

Q: An extruded beam has the cross section shown. Determine the location e of the shear center O. 5 mm B…

A:

Q: The truss is subjected to the loading shown. It is supported by a pin at A and a roller at L.…

A:

Q: lo' lo 0.SP

A:

Q: Determine the shear value when x = 6m (from the left) for the beam shown Where: P1 = 61kN; P2 =…

A: Equipibrium equation in x direction and in y direction  Cut the plane from left end at 6m end and…

Q: a plane truss is loaded as shown. determine the forces members BC, CE and BF.

A: Truss: A truss is a structure consisting of members arranged in linked triangles so that the entire…

Q: Calculate the required spacing of 10-mm-diameter ties, s (mm). Calculate the nominal axial strength…

A: Short column: - A column whose slenderness ratio is less than or equal to 12 called short column.

Q: using method of sections. Determine the forces in members BC, BG, and FG.

A:

Q: All angles in this bridge are either 90 degrees or 45 degrees Suppose that the applied force F =…

A: Given:F = 250.0 NRequired:Force in member between joints 1and 2

Q: In the plane truss system, the loading status of which is evident in the figure, the support…

A: Draw the free body diagram.

Q: 3

A:

Q: Each of the links AB and CD is made of steel (E = 29 x 106 psi) and has a uniform 1 rectangular…

A: Given : E = 29 X 106 psi Cross section = 1/4 X 1 in. Determine the largest load which can be…