The below network diagram consists of Rustaq, Middle and Sohar networks. Both Sohar and Rustaq network uses UTP cable with data rate of 100 Mbps. A) What is the network address of Rustaq, Middle and Sohar networks? B) Identify the category of the UTP cable in Sohar and Rustaq networks. C) What is the need of DNS & DHCP server in Sohar networks?

The below network diagram consists of Rustaq, Middle and Sohar networks. Both Sohar and Rustaq network uses UTP cable with data rate of 100 Mbps. A) What is the network address of Rustaq, Middle and Sohar networks? B) Identify the category of the UTP cable in Sohar and Rustaq networks. C) What is the need of DNS & DHCP server in Sohar networks?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

8. Answer the questions below based on the given network topology: (a) How many collision domains are there? (b) How many broadcast domains are there? (c) What type of cable (straight-through or crossover) is required to connect PCO and Switch0? (d) What type of cable (straight-through or crossover) is required to connect two PCs? (e) If PCO wishes to discover the MAC address of PC1, which network protocol should be utilized?
The below network diagram consists of Rustaq, Middle and Sohar networks. Both Sohar and Rustaq network uses UTP cable with data rate of 100 Mbps. A) What is the network address of Rustaq, Middle and Sohar networks? B ) Identify the category of the UTP cable in Sohar and Rustaq networks. C) What is the need of DNS & DHCP server in Sohar networks?
B(i) Propose ONE (1) suitable device to be added into the network topology to ensure communication among hosts in VLAN 10 and VLAN 20 as shown in Figure 2-1.Redesign and redraw an updated network topology with the new device added.[You may draw your answer on paper, then snap the image to put into the answer file.]
Problem Solving. Category5 cable, commonly referred to as CAT-5, is a twisted pair cable for data networks. Since 2001, the variant commonly in use is the Category5e specification (CAT-5e). The cable standard provides performance of up to 100MHz and is suitable for most varieties of Ethernet over twisted pair up to 1000BASE-T(Gigabit Ethernet). We would like to transmit information over a CAT-5 twisted pair cable at 500 Mbps. (a)What is the signal-to-noise ratio (SNR) of 30 dB adequate to transmit 500 Mbps? (Convert the SNR of 30 dB to a numerical value then apply the Shannon Theorem). (b) What is the SNR required to just adequately transmit at 500 Mbps? Express your answer in decibels for the SNR(that is, SNRdB)
part 1: List down the services provided by the data link layer. part 2: Suppose there are 4 nodes sharing a broadcast channel using TDMA protocol. Suppose at time t=0: Node 1 has three frames to transmit, Node 2 has two frames to transmit, Node 3 has no frame, Node 4 has four frames to transmit. The length of time slot is 2 seconds whereas time needed to transmit one frame is 1 second. Explain how TDMA will work and how much time will be taken to transmit all of these frames? part 3: Do we need to use multiple access protocol in following cases? Lab computers connected to a layer 2 switch through Ethernet cables (star topology) Two computers in an Ethernet bus topology Your laptop is connected to BIIT network through a WiFi link Answer, yes or no and then justify…
Quèstion 24 Consider the figure below, with three links, each with the specified transmission rate and link length. ELink 1 Transmission rate: 1000 Mbps Link Length: 1 Km Link 2 +Link 3- Transmission rate: 100 Mbps Link Length: 1 Km Transmission rate: 10 Mbps Link Length: 5000 Km Assume the length of a packet is 16000 bits. The speed of light propagation delay on each link is 3x10^8 m/sec What is the transmission delay of link 2? 0.5 second O A 0.0016 seconds OB. 0.016 seconds OC. None of the above OD.
Examine Figure 1-1l shown below and answer the following questions: East Office (Bulding B) network address 192 168.1.0 West Office (Bulding A) network address 192.168 20 Distance B Between Routerd and Switcho is 3 meters PCO with low data transmission Switcho Routero PC1 2950 model Routert Distance A Between Router1 and Routero is 300 meters. PC2 Figure 1-1: Local Area Network Topology 6) Propose the appropriate cable that should be used to connect the Distance A and Distance В. (ii) Discuss TWO (2) differences between the cables that you have proposed in Question 1 c) (i) above.
Question 4: Consider the figure below, with three links, each with the specified transmission rate and link length. +Link 1+ Link 2 +Link 3+ Transmission rate: 1000 Mbps Link Length: 1 Km Transmission rate: 10 Mbps Link Length: 2 Km Transmission rate: 100 Mbps Link Length: 5000 Km Assume a packet length of 8000 bits is transmitted from host to destination. 1. Find the delay on each link for one packet. 2. Find the end to end (host to destination) delay for one packet Consider transmission delays and propagation delays but ignoring queuing delays and processing delays. Formulas: Transmission delay= Length of packet in bits / Transmission rate Propagation delay = distance between two nodes / 3 x 108 m/s Total delay at each link= Transmission delay + Propagation delay
Design an Ethermet LAN network to operate with 150 Mbps that has Q6] the same frame fomat used in Fast Ethernet, answering the following items: Minimum frame time, ii- i- Maximum length of the network, i- If frame change is available as design factor, how can the 150 Mbps network has the same MaxLength with 100 Mbps Fast Ethernet, give the minimum frame length.
1) Consider a reliable data transfer protocol that uses only negative acknowledgments. Suppose the sender sends data only infrequently. Would a NAK-only protocol be preferable to a protocol that uses ACKs? Why? 2) Besides network-related considerations such as delay, loss, and bandwidth performance, there are other important factors that go into designing a CDN server selection strategy. What are they? 3) What are the five layers in the Internet protocol stack? What are the principal responsibilities of each of these layers? List five tasks that a layer can perform. 4) Why do HTTP, SMTP, and POP3 run on top of TCP rather than on UDP? 5) List six access technologies. Classify each one as home access, enterprise access, or wide-area wireless access, and then describe how they fundamentally operate.
Discuss Below Given Question. Consider building a CSMA/CD network running at 1 Gbps over a 1km cable with no repeaters. The signal speed in the cable is 200000km/sec. What is the minimum frame size?
Question 1. 200 nodes are connected to 1,500-meter length of coaxial cable. a Using some protocol, each node can transmit 50 frames/second, where the average frame length is 2,000 bits. The each node is 100 Mbps (where 1 Mbps transmission rate at = 1,000,000 bps). What is the efficiency of this protocol?