the béginning of An ideal Diesel cycle has a compression ratio of 16.6. process, air is at 540 R and 14.7 psia. At the end of the heat-addition process, air is at 3160 R. Utilizing the cold-air-standard assumptions, determine the following for this cycle: (a) The thermal efficiency AND the cutoff ratio. (b) The exergy that is lost associated with each of the four processes and the cycle, assuming a source temperature of 3160 R, and waste heat is rejected to the surroundings at 540 R. compression

the béginning of An ideal Diesel cycle has a compression ratio of 16.6. process, air is at 540 R and 14.7 psia. At the end of the heat-addition process, air is at 3160 R. Utilizing the cold-air-standard assumptions, determine the following for this cycle: (a) The thermal efficiency AND the cutoff ratio. (b) The exergy that is lost associated with each of the four processes and the cycle, assuming a source temperature of 3160 R, and waste heat is rejected to the surroundings at 540 R. compression

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A newly purchased sedan car operates on an ideal thermodynamic cycle. The engine has acompression ratio of 10. The ambient air pressure is 1 bar while temperature is 21 ºC. Themaximum temperature in the engine is 1600 K. Draw the ideal power cycle and label it.Utilizing the air-standard assumptions, determine (a) the gas temperature at the exits of thecompression and the expansion processes, (b) the specific works of compression, expansionand net, (c) heat supplied to the engine and (d) the thermal efficiency.
At the beginning of the cooling process of an ideal Brayton cycle, the pressure and temperature of the air are 150 kPa and 480°C. The state of the air leaving the compressor is 1.2 MPa, 320°C. Assuming constant specific heats (R=0.287 kJ/kgK, cv=0.718 kJ/kg K, cp=1.005 kJ/kg K), determine the back work ratio of the cycle.
Consider an ideal Brayton cycle using air as the working fluid, operating with a pressure ratio of 17. Air at 50 kg/s enters the compressor at 150 kPa and 700 K. The air then enters the turbine at 3000 K. Assume gas constant and specific heats at room temperature. Apply the ideal gas equation of state and isentropic relationships of ideal gas appropriately. (а) Analyse all pressures and temperatures in the cycle (b) Using values of Qin, Qout and Wnet in MW, determine the thermal efficiency of the суcle. (c) Illustrate proper P - v and T –s diagrams for the cycle, indicating all pressures and temperatures obtained in (a).
3. In a gas turbine plant air is compressed from 1.01 bar and 15 °C through a pressure ratio of 5. It is then heated in a combustion chamber at constant pressure to a temperature of 700 °C and expanded to atmospheric pressure in a turbine. The isentropic efficiencies of compression and expansion are respectively 0.8 and 0.85. Calculate (a) the cycle efficiency and (b) the work ratio. Assume that the properties of air do not change with temperature and may be taken as Cp = 1.005 kJ/kg K and y = 1.4.
An open cycle gas turbine power plant Air is supplied to the compressor at 1 bar and 23°C. The air is compressed to a pressure of 5.5 bar and a maximum temperature of 700°C. The hot air expands. through the turbine to a pressure of 1 bar, assuming a standard air cycle. and compression and expanding according to the Eisentrowing process, calculate (a) power plant efficiency; and (b) the ratio between the work to drive the compressor and the work produced by the turbine
A steam powerplant runs using the Rankine cycle. The boiler operates at 5000 kPa and 500 °C. The turbine exhaust is saturated steam at 30 kPa and the pump efficiency is 0.75. Based on this information, select all the correct statements below. a. If the powerplant is operated isentropically, the turbine output will be wet steam with 0.78 quality. O b. If the powerplant is operated following the Carnot cycle, the thermal efficiency will increase by 118% C. If the condenser pressure is decreased, the overall thermal efficiency will also decrease. O d. If the powerplant is operated isentropically, the energy output of the turbine will be 1179 kJ/kg O e. The efficiency of the turbine is 0.75 Of. The overall thermal efficiency of the power plant is 0.255
A 150 MW gas turbine power plant running on Ideal Brayton cycle has the following initial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature at the turbine is 910°C. Draw the P-V and T-S diagrams and determine the following: d. Thermal Efficiency e. Mass flow rate, kg/min
! Required information Problem 09.034 - Ideal Otto Cycle with Variable Specific Heats - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 95 kPa and 27°C, and 760 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Take into account the variation of specific heats with temperature. The gas constant of air is R = 0.287 kJ/kg-K. Problem 09.034.a - State After Heat Addition in Variable Heat Capacity Ideal Otto Cycle Determine the pressure and temperature at the end of the heat-addition process. (You must provide an answer before moving on to the next part.) The pressure at the end of the heat-addition process is 3915.8 kPa. The temperature at the end of the heat-addition process is 1647.7 K.
Hello Sir,Good Night.I have a question in my homework related thermodynamics lesson.The following below is my question. Please advice, thank you
In a Rankine Cycle, real work produced by the turbine is less that the isentropic work. True False
What four processes make up the simple ideal Brayton cycle?
With given,find,figure,analysis, and interpretation