The beam shown has an overall length L of 2 metres. A uniform distributed load of 3.0 kN/m is applied as shown. If the distance x is 1 metre, what is the equation for the resisting bending moment (M) in section a-a of the beam. O a. M = 3.00x - 2.12 kNm O b. None of these options O C. M = 6.00x-3.0 kNm O d. M = 3.0x -4.50 kNm O e. M 9.00x +2.35 kNm X-

The beam shown has an overall length L of 2 metres. A uniform distributed load of 3.0 kN/m is applied as shown. If the distance x is 1 metre, what is the equation for the resisting bending moment (M) in section a-a of the beam. O a. M = 3.00x - 2.12 kNm O b. None of these options O C. M = 6.00x-3.0 kNm O d. M = 3.0x -4.50 kNm O e. M 9.00x +2.35 kNm X-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) The gudgeon pin is used to connect the piston and the connecting rod. Show from first principles that the maximum bending moment acting on the gudgeon pin is given by: PL M = 8 where P is the maximum gas load and L is the length of the pin
Find the support reactions, draw the free-body diagram of the beams that shows the reactions and the equivalent loadings of the beams. Show the computation where M0 = 1,220 N-m, P = 2650 N, F = 3000 N, w0 = 1702 N/m, w1 = 1103 N/m, a = 3 m, b = 6 m, c = 2 m
Find the reactions of the structure and draw the shear and moment diagrams for the beam (Use the Force Method).
The Figure shows a loading set up similar to that of the 'Bending in Beams' laboratory experiment. E = 200 GNm"2 and I = 2 x 109 m“. The bending moment and the radius of curvature at any point in the beam between the support points B and C are respectively: 1 kN 1 kN B 0.125 m 1.25 m O a. (-)125 Nm, 1.2 m O b.(-)12.5 kNm, 2.8 m O C. (-)2.5 kNm, 2.4 m O d.(-)125 Nm, 3.2 m
Q1 A simply supported beam of length 5m, carries a uniformly distributed load of (Your Roll No. kN/m) extending from the left end to a point 2m away. There is also a clockwise couple of (1200+Your Roll No. kNm) applied at the centre of the beam. Draw the S.F and B.M diagrams for the beam and find the maximum bending moment.
Read Properly & Please provide Correct Answer.
A simply supported beam of hollow rectangular cross section is 100mm deep and 60mm wide with a wall thickness of 10mm. The beam has a span of 6m and carries a load as shown . Neglecting the weight of the beam draw a bending moment diagram and calculate the maximum bending moment. And determine the maximum bending stress in the material.
Draw the shear stress diagram and bending moment diagram for a beam with the free body diagram shown below. Identify the location of critical point(s) in the beam. Given AB = 0.5 m, BC = 0.6 mm, and CD = 0.5 m.
Q4 A solid rectangular homogeneous section (total length = 7.2m) is simply supported, where b = 50 mm and d = 175 mm. A concentrated load F= 140 N acts at point C where L1= 4.00 m L2 = 3.20 m. Calculate the maximum bending stress and give your answer in N/mm² to 2 decimal %3D places. *Assume the weight of the beam is negligible and zero. F 200. L1 L2 b d A F B
A simply supported wood beam with a span of L = 11 ft supports a uniformly distributed load of w = 840 lb/ft. The allowable bending stress of the wood is 1400 psi. If the aspect ratio of the solid rectangular wood beam is specified as h/b = 1.5, determine the minimum width b that can be used for the beam. O 5.54 in. O 7.03 in. O 6.62 in. O 8.58 in. O 4.15 in. L h
Q1) A simply supported beam is 3 m long and carries a vertical load of 5 kN at point lm from the left-hand end. At a section 2 m from the left- hand end a clockwise couple of 3 kN.m is exerted, the axis the couple being horizontal and perpendicular to the longitudinal axis of the beam. The cross section of the beam shown in the figure. Determine the maximum bending stress set-up. 60 All dimensions in mm 120 120 ENT NEERING
Q2: A conveyor beam has the cross section shown below and it is subjected to a ben moment. Determine the maximum permissible bending moment which can be applie the heam when the hottom flange in tancion, if the safe stor for the mate tension and compression are 30 MPa and 150 MPa respectively. T C VI 25 mm 150 mm 100 mm 50 mm المانه *50*100*50* mm mm mm