The AE cable carrying the concentrated loads is attached to the rod EN, which has two ends of the hinges. The rod EN stands vertically with the cable EG. a = 2 m, b = 8 m, c = 4 m, d = 6 m, P = 10 kN. a) Find the reaction forces at the pins A and G, the force on the rod EN. Draw all the required free body diagrams. a) Find the vertical distances of yAs and yAD. Draw all the reguired free body diagrams.

The AE cable carrying the concentrated loads is attached to the rod EN, which has two ends of the hinges. The rod EN stands vertically with the cable EG. a = 2 m, b = 8 m, c = 4 m, d = 6 m, P = 10 kN. a) Find the reaction forces at the pins A and G, the force on the rod EN. Draw all the required free body diagrams. a) Find the vertical distances of yAs and yAD. Draw all the reguired free body diagrams.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 4: The wall crane supports a load of 800 lb. Determine the horizontal and vertical components of reaction at the pins A and D. Also, what is the force in the cable at the winch W? 4 ft- E W 800 lb
The compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin) at D. Determine the reactions at the supports. Neglect the thickness of the beam. Ak 4 k 30° ܘܐܝܐ A ANAS DOLL 15 k. ft D B States Yk 3 4 Bft C ft 8 ft Aft 4 ft 2 ft 8. What is the shear at a point (A + 4) ft left of point C? (k) 9. What is the shear at a point (A + 8 + C/2) ft left of point C? (k) 10. What is the moment at point C? (k-ft) Use: A= 8 B= 6 C= 8 Y= 29
Cable Eメ了 The beam AB shown 50 weighs 10N/ m Supported by at A and B hinge 280 N and Cable at a B. Delermine The reactions at A and the tensiin in the cable
Problem 4) Assume the loads applied to the beam result in a uniformly horizontally distributed load 10 k. What is the once transferred to the cable. The loads have magnitudes Pi = 8 k and P2 distributed load acting on the cable w, and what are the vertical support reactions at A and C? E 4 ft l space 8 ft dest A B P1 P2 3 ft 14 ft 8 ft 14 ft 3 ft 8 ft
a = 6.0 mb = 7.0 mc = 23 kNd = 48 kN
Determine the vertical reaction at each support (Ay, By, Cy, Dy and Ey) for the beam below. 15 kN/m E B El = constant
Equilibrium
50 N 40 N/m 2.5 m 80 N B 30-| 60° 1 m 3 m 1.5 m 30° A Determine the support reactions at pin A and roller B. Neglect the thickness of the beam.
For the truss shown in the figure below, assume that the loads are being transmitted to the bottom chord and draw the influence lines for member DI and EK. Also, considering the 3-point moving load as shown, determine the following member forces. Assume that the loads move only to the right. a. Maximum tension on member DI in kN, put “0” if none. b. Maximum compression on member DI in kN, put “0” if none. c. Maximum tension on membe EK in kN, put “0” if none. d. Maximum compression on member EK in kN, put “0” if none. a= 5.1 m b= 6.3 m c= 62 kN d= 78kN