The adjustable pliers are used to clamp the smooth tube C. If the force of 100 N is applied to the handles, determine the state of stress at points A and B on the cross section of the jaw, at section a-a. Give the results on one element at each point. 20 mm 25 mm) 25 mmX 10 mm 151 Section a-a mm -250 mm- 100 N 100 N

The adjustable pliers are used to clamp the smooth tube C. If the force of 100 N is applied to the handles, determine the state of stress at points A and B on the cross section of the jaw, at section a-a. Give the results on one element at each point. 20 mm 25 mm) 25 mmX 10 mm 151 Section a-a mm -250 mm- 100 N 100 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 520-kg engine is suspended from the jib crane at the position shown. Determine the state of stress at point B on the cross section of the boom at section a -a. Point B is just above the bottom flange. (Figure 1) Figure 2m 2m 2m- 4 MP A D 0.4 m 150 mm 150 mm . Determine the normal stress at point B Express your answer using three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. Submit μA B = 3.85 Units You have already submitted this answer. Enter a new answer No credit lost. Try again. TB = n → Previous Answers Request Answer Submit Determine the shear stress at point B. Express your answer to three significant figures and include the appropriate units. HA ? Value Request Answer Ć Units P ?
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 20 kN applied at A. Assume a = 270mm, b = 170mm, c = 70mm, and 9 = 50°. Pin B is in a double-shear connection and has a diameter of 24 mm. The bell crank has a thickness of 36 mm. Determine the bearing stress in the bell crank at B. Answer in MPa rounded-off to 2 decimal places. F₁ Bell crank Support bracket Add your answer B b 4
5) The bolt has a diameter of 20 mm and passes through a tube with an inner diameter of 50 mm and an outer diameter of 60 mm. If the bolt and tube are made of A-36 steel, determine the normal stress in the tube and bolt when a force of 40 kN is applied to the bolt. Assume the end caps are rigid. 40 kN 160 mm 150 mm 40 kN
roblem The two members are connected by two 20-mm bolts. If P = 10 kN, determine the normal and shear stresses in the bolts and the maximum bearing stress on the member. The nuts have an outer diameter of 30 mm. P P Guides to solve the problem: 12 mm Front view: 30° 1. Draw the FBD of one member. 2. Solve for the bearing force. 3. Section one bolt and solve internal forces. 4. Solve for the normal and shear stress in the bolts. 5. Solve for the bearing stress in the members due to the nuts. 6. Solve for the bearing stress in the members due to the bolts. 36 mm 36 mm P P
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths.
Determine the normal stress at A and B if the blade of the coping saw has a tension of 40 Newtons. Ans: 123 MPa @A, 62.5 MPa @B 8 mm 75 mm 1A 3 mm 8 mm 3 mm B 100 mm 50 mm
The beveled gear is subjected to the loads shown.Determine the stress components acting on the shaftat point B, and draw the results on a stress elementat this point. The shaft has a diameter of 1 in. and isfixed to the wall at C. A = 0.7854 in2 J = 0.098175 in4 I = 0.049087 in4 (QB)z = 0 (QB)x = 0.0833 in3
The supporting wheel on a scaffold is held in place on the leg using a 4- mm -diameter pin as shown. If the wheel is subjected to a normal force of P = 2.3 kN , determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on the wheel.
- The bell-crank mechanism is in equilibrium for an applied load of F₁ = 15 kN applied at A. Assume a = 270mm, b = 170mm, c 70mm, and 9 50°. Pin B is in a double-shear connection and has a diameter of 20 mm. The bell crank has a thickness of 34 mm. Determine the bearing stress in the bell crank at B. Answer in MPa rounded-off to 2 decimal places. F₁ Bell crank Support bracket a B b
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a = 270mm, b = 150mm, c = 70mm, and 0= 50°. Pin B is in a double-shear connection and has a diameter of 33 mm. The bell crank has a thickness of 39 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket F₁ Answers: Ob Tpin B = Bell crank Bu CI B MPa MPa F₂
Determine the maximum value of the force P (kN) that can be applied to member AD if the allowable stress is 200 MPa and the maximum upward displacement of point A is 3 mm. Use E=100 GPa The values of the cross-sectional area, and L1, L2, and L3 are given in table below for each student. P A L1 12 kN L2 9 kN L3 LI (m) (m) Student Cross-sectional area L2 L3 ID (mm?) (m) 1.45 1131731 200 3.8 1.2
The yoke-and-rod connection is subjected to a tensile force P. The end of the 40-mm diameter rod is embedded inside a wall at a length I of 100 mm using epoxy adhesive. If the allowable normal stress for the rods is 60 MPa, the allowable shear stress for the 25- mm diameter pin A is 50 MPa, and the allowable shear stress of the epoxy adhesive is 6 MPa, determine the largest force P that can be applied to the assembly. Note: Show your calculations for all types of stresses in detail. 40 mm 30 mm A 25 mm P.