The A-36 steel bar AB has a square cross section. Figure 1.5 in. 30 10 ft <1 of 1 1.5 in. +H 1.5 in. Part A If it is pin connected at its ends, determine the maximum allowable load P that can be applied to the frame. Use a factor of safety with respect to buckling of 2.07. (Figure 1) Express your answer with the appropriate units. μÅ 3 ? P= Value Units Submit Provide Feedback ▼ Request Answer

The A-36 steel bar AB has a square cross section. Figure 1.5 in. 30 10 ft <1 of 1 1.5 in. +H 1.5 in. Part A If it is pin connected at its ends, determine the maximum allowable load P that can be applied to the frame. Use a factor of safety with respect to buckling of 2.07. (Figure 1) Express your answer with the appropriate units. μÅ 3 ? P= Value Units Submit Provide Feedback ▼ Request Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E= 200 GPa. A P1 L1 E Dia. 1 L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 Dia. 2 P1 P2 P3 L1 L2 L3 Name (mm) (mm) (kN) (kN) (kN) (mm) (mm) (mm) 45 40 100 35 30 1300 2100 1300
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
Question 27 1 points Save Ans A built up l-section is formed from plates welded together as shown in the figure. It is to be used as a column L = 3.8 m long. All elements are A36 steel and connected such the section is fully effective Using the following properties, calculate the flexural buckling stress, Fcr, in MPa using theoretical k. Flanges: b = 150 mm, te = 18 mm Web: h = 310 mm, tw = 7 mm Write your final answer in two decimal places only. I. tf
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 L3=1350 GPa. L2=2150 A L1 E Dia. 1 L1=1350 Р3-25 P1 L2 Dia. 2 P2=40 P2 P1=105 Dia2=45 L3 P3 D D 35 mm o Dia1=60
ASAP
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
2. Given a simply supported beam shown in figure below with the cross section at maximum moment. The beam supports a uniform service dead load of WDL =30 kN/m (excluding own weight of beam), PLL = 270 kN. Use fc' = 30 MPa; fy = 400 MPa. Calculate design strength M, for the cross section shown in the figure. Check the strains in the steel ɛsi. P, LL 75 100 - - 75 90 W. DL 710 650 5Ф30 15000 mm-
M E You have 2 Thank You Best Regare Ms. Nur Akr Figure Q3 shows a truss structure, which is pinned at A and roller supported at B. Horizontal load are applied to the truss as shown in the Figure. By using section method, solve the force in member AC, CD and DE in the figure shown (CO2, PO2, C3). 20KN 10KN 3.5m H →10kN 3.5m E 3.5m D H 15kN 10kN- 5kN G C A 5.0m 3.5m B 000 5kN 5kN Gmail M
Consider the simply supported truss as defined in the figure and parameter table. Find the force in members CD, HD, and HG. Follow the convention the tension is positive and compression is negative. A 1910 P. B cc 000 BY NỌ SA 2021 Cathy Zupke L₂ parameter value L₁ 1.5 L2 1.5 L3 2.5 LA 2 1.5 1.5 30 50 60 60 L5 L6 P₁ P₂ P3 P₁ units H # G P₁ E F The force in member CD = The force in member HD = The force in member HG = m m EEEEEZZ m m m L3 KN KN ↑ KN KN KN 3
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E0=205GP,, Ga=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x10-mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, caD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
Part (b) (A hollow circular steel drive shaft has an outer radius of R mm and an inner radius of r mm as shown in Figure Q9-b. Figure Q9-b: Given that r-16, R-30 and the maximum allowable shear stress in the shaft is 75 N/mm2, calculate the maximum permitted torsional moment, T., that can be transmitted by the shaft. T: [(b)