The 60-lb door shown in (Figure 1) has its center of gravity at G.FigureB24 in.+24 in.+A18 in.18 in.DE1 of 1 >Part ADetermine the components of reaction at hinge A if hinge B resists only forces in the z and y directions and A resists forces in the x, y, z directions.Enter the z, y, and z components of the reaction separated by commas. Express your answers in pounds to three significant figures.—| ΑΣΦ | 11 | vecAz, Ay, A₂=SubmitPart BB₁, By =SubmitRequest AnswerDetermine the components of reaction at hinge B if hinge B resists only forces in the z and y directions and A resists forces in the z, y, z directions.Enter the z and y components of the reaction separated by a comma. Express your answers in pounds to three significant figures.AE Ivec 4Provide FeedbackRequest Answer?MIC ?lblb

The 60-lb door shown in Figure 1) has its center of gravity at G. ▾ Part A Determine the components of reaction at hinge A if hinge B resists only forces in the z and y directions and A resists forces in the z, y, z directions. Enter the z, y, and components of the reaction separated by commas. Express your answers in pounds to three significant figures. ΠΫΠΑΣΦΠ Ag, Ag. Age Submit Request Answer ← → O lb

The 60-lb door shown in Figure 1) has its center of gravity at G. ▾ Part A Determine the components of reaction at hinge A if hinge B resists only forces in the z and y directions and A resists forces in the z, y, z directions. Enter the z, y, and components of the reaction separated by commas. Express your answers in pounds to three significant figures. ΠΫΠΑΣΦΠ Ag, Ag. Age Submit Request Answer ← → O lb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.39P: The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables...

See similar textbooks

Similar questions

The structure is supported by a pin at C and a cable attached to A. The cable runs over the small pulley D. Find the internal force systems acting on sections 1 and 2.
Two concrete blocks weighing 320 lb each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown?
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
A carpenter holds a 12-lb 2-in. by 4-in. board as shown. If he exerts vertical forces on the board, determine the forces at A and B (use positive if the force is up and negative if down). Answers: NA = NB = i i 3' B eTextbook and Media 7' lb lb
Determine the 5940 lb reactions at point A and B of the parallel force system shown in the figure to the right. Neglect the weight of the supporting member. 1170 lb/ft Es.00+ 4.00- -5.00- 6.00- LENGTH IN FEET Question 4 Listen Use the sum of the vertical forces to calculate the magnitude of reaction at A. Your Answer:
The oven door is spring loaded at C and pinned at A. Determine the magnitude of the normal force at section a-a that lies just to the right of C if W = 24.6 lb and 0 = 32°. B 8 in. O 20.9 lb O 21.7 lb O 18.6 lb O 19.3 lb O 22.4 lb 10 in.- 5 in. 12 in.
A carpenter holds a 14-lb 2-in. by 4-in. board as shown. If he exerts vertical forces on the board, determine the forces at A and B (use positive if the force is up and negative if down). Answers: NA = NB = i i 3' 238 252 B 9' lb lb
240 lb B 2. Find the horizontal and vertical forces at Point C as it acts on Member BD. D 45° 450 E -8'-
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
1. Draw the FBD of the entire structure (weight acts at point G) 0.5 m 0.5 m 0.5 m 1 m C 10 B 2. Draw the FBD of member AC A R 20 B -1 m- 60° -2 m A 3. Draw the FBD of member ABC 0.5 m B C E 1 m 4. Draw the FBD of member DABC 12 in. 12 in. A 150 lb 45° B a -3 ft 5. Draw the FBD of members ABC and BD 4 m- -5 in D C -12 in. B C 2.5 kN 60⁰° 6. Draw the FBD of members ABC and CD -3 ft- DO -6 m 1.5 ft + 1.5 ft 4 kN-m B D 3 m
Given the figure determine the bar force at BD and AB