The 2N5459 has a rating of gmo VGS(off) = -8 V. = 4 ms determine the value of gm at VGs = -3 V. For this JFET,
Q: QUESTION 10 Determine RT and IT RT= IT = Vs 120V R1 2.2kQ units units R2 1.5kQ R3 50092 R4 4kQ2
A:
Q: Q.) Determine the rms value of the function i(t) = 11 – 1 sin 2t A.
A:
Q: By using only two op-amps, design a circuit that can perform the following operation: Vo == Also,…
A:
Q: 6. What is the Q of this filter? A) 3.16 B) 62.8 C) 10 D) 7.92
A: The series RLC circuit with R=10ohms, c=1mF and L=1H. Need to find the quality factor of the…
Q: Find the Laplace transform of the following time functions using MATLAB
A: Given functions are We need to determine the Laplace transform of above functions using MATLAB.
Q: Explain why λ/2 dipole antenna gives optimum radiation pattern.. Provide your answer Handwritten…
A:
Q: Neglecting saturation, if the current taken by a series motor is increased from 10 A to 12 A, the…
A: A DC series motor by Neglecting saturation having, Initial current, I1=10 A Final current, I2=12 A
Q: 4 use eqation as show in picture design logic circuir ? 4.1 use NAND only 4.2 use NOR only
A:
Q: The discrete time x[n] signal is defined as x[n] = 28[n+ 1]+ (3- n)(u[n] -u[n - 3]). Accordingly,…
A:
Q: 3. Can you use the concept of the "wavefront continuation" the Snell's law of reflection? to explain
A: We have to explain whether we can you use the concept of wavefront continuation to explain the…
Q: 3. The per phase impedance of a short transmission line is 0.3 + j0.4 ohm. The sending-end…
A:
Q: WYE configuration
A:
Q: Find the midband gain in dB and the upper cut off frequency for the high pass filter if R1 = 10k and…
A:
Q: Consider an LTI system with impulse response h(t) = u(t), find out the output y(t) for a given input…
A:
Q: Calculate the active power in a 487 H inductor. a) 2482 W b) 1545 W c) 4565 W d) O W
A: it is asked to find active power in 487H inductor
Q: Find the current in the 12 resistor in the figure below. (R₁3.00, R₂ = 6.60, AV = 11 V) R₁ www 4.00…
A:
Q: 2. Explain why the steady-state power density in space is zero for an EM wave incident on an ideal…
A: When an electromagnetic (EM) wave encounters an ideal conductor, it induces an electric current in…
Q: 5. current input Consider the system shown below. Assume that the system is subject to a step (a)…
A: Since you have posted a question with multiple subparts, we will provide the solution only to the…
Q: Q4) Consider the following PCM transmitted signal 1 0 A 0 -A I I I 0 I I a. b. I 0 I 1 0 I 0 1 1 I 1…
A: The PCM transmitted signal is a) We need to determine type of the line code in this PCM transmitted…
Q: [60 Hz; 11.5 kV] 3. A 3 phase, 4-pole, star - connected alternator has 24 slots with 12 conductors…
A:
Q: A magnetic circuit with a single air gap and a single coll is snown in the rigure below. Core…
A:
Q: A capacitor of 2 mF has a voltage of 525cos(201). The energy stored in it at t= 850 ms is: a. 36.22…
A: Given, Capacitor C=2mF Voltage across capacitor =525cos(20t) We have to calculate the energy stored…
Q: An ac generator with a frequency of 80Hz and an rms voltage of 43V is connected in series with a…
A: Given: AC source with frequency, f = 80 Hz and rms voltage, Vrms=43 V,. Voltage source is in series…
Q: 6.24.2 In the circuit below, all the capacitors have already reached steady state (no current…
A: In this question we need to find the energy stored in the capacitor C5
Q: What do the connection angles and groups show in transformers? For example, where are the Yy0 , Dy5…
A: It is asked what do the connection angles and groups show in transformers. Also it is asked where…
Q: A single phase, 100 ampere load is located 1000 m from a 480 V electrical power source. What minimum…
A:
Q: 10MVA 10% G₁ LL X₁ 10 MVA 5% 20MVA 15% G₂ X₂ 8 MVA 4% 20MVA 15% G3
A: We need to find out the equivalent circuit diagram for the power system network.
Q: me op amp in the circuit in (Eigure 1) is ideal. Suppose R-15 kl. ure 8k0 w w 25 kn 32 k 15 V -9V…
A: We need to calculate the output voltage expression, Vs max and min value for output will not…
Q: O Before the first rising clock, so in the initial state, what is z? Inputs: b Outputs: y, z 00 01 O…
A:
Q: According to the Kp and Kd in which selected, our closed (ROok - 1OCUS Meinod Closed loop diagram…
A: The plant transfer function of a system is Gs=1s+K. It is controlled by a PD controller in a unity…
Q: 1. Determine io in the circuit of Fig. 1 using the superposition principle. 2. Use SPICE to verify…
A: The given circuit diagram is shown below,
Q: Investigate if the following systems are memoryless, linear, time-invariant (TI), causal, and…
A: For the systems described by the following input-output relationship: a yt=xt-2+x2-t,b…
Q: 2. A source transform is performed on the s-domain representation of the time- domain circuit shown.…
A: Time domain circuit Circuit in s-domain To determine: Value of Ig(s)
Q: Design a 4-bit 4x1 multiplexer using four 4x1 multiplexers please do not write other examples on the…
A: Asked to design 4×1 multiplexer using 4×1 multiplexer
Q: 10. If you want the gain of the filter at 50 rad/sec to be 10 dB, what value will the 9 k resistor…
A:
Q: For the timing diagram shown below, is it a Mealy or Moore machine? vur Clock X Output Please choose…
A:
Q: Exercise 4: Determine the impulse response h[n] of the following first-order system: y[n] = -0.5y[n…
A: given that y(n) = -0.5 y(n-1) -4x(n) +5 x(n+1)
Q: P=VI S = VI* compliance SA * I = (Bengtive *= I* ue: سو اوسته + * Prerative Methed Ze
A: Apparen
Q: Solve the following problems 1. A 4-pole, D.C. generator has a wave-wound armature with 792…
A: Since you have posted multiple questions, we will provide the solution only to the first question as…
Q: Find the Norton equivalent for the voltage divider circuit shown: 10V battery 10k 10k
A: We need to find out Norton current and Norton resistance for given circuit.
Q: a) Find I in the network shown below using source transformation. 6 ΚΩ 6 ΚΩ
A:
Q: جاء في الامتحان H. W3 A steel wire has a radius of (2mm) and a conductivity of 2x 10° S/m. The steel…
A:
Q: 3. Find the s-domain transfer function for this circuit. There are no initial conditions. A) H(s) =…
A: Given Data: An inverting Op-Amp with, Input Voltage =Ui Output Voltage =Vi To Find: Transfer…
Q: H. W3A steel wire has a radius of (2mm) and a conductivity of 2× 10° S/m. The steel wire has an…
A:
Q: 240 V' HI I R₁ Μ 3 Ω + V3 R3 R₂ Μ 5Ω 4Ω Μ R4 2 Ω + V5 R5 6Ω Μ R6 1 Ω + V₁ R₁ 2 Ω 17
A: We need to find out the value of I,I7,V3,V5,V7,power dissipated in R7 Circuit:-
Q: Consider the LTI-system characterized by the difference equation y[n] = 0.25x [n] +0.5x[n 1] +0.25x…
A: Given: Difference equation of an LTI system, y[n]=0.25x[n]+0.5x[n-1]+0.25x[n-2], To find: d)…
Q: E = 28 V - 4₁. + V₁ R₁ 12 ΚΩ 112 ΚΩ R3 3 ΚΩ Μ R₁ 9 ΚΩ R5 Μ 6 ΚΩ + Vs – R6 16 • 10.4 ΚΩ
A:
Q: Determine the total potential energy stored, in microjoules, in a sphere of radius 6 m if the…
A: To determine the total potential energy stored in the sphere, we need to integrate the energy…
Q: 14. For a power transformer operating at full load it draws voltage and current equal to 200 V and…
A: It is given that: V=200 VoltI=100 Acosϕ=0.8 pfsince Pi and Pcu are nominal losses therefore it cant…
Q: QUESTION 2 The peak-to-peak voltage is 40V, its rms voltage is 14.1 V 11.4V 13.3V 12.3 V
A: In this question we need to find the RMS value
Step by step
Solved in 3 steps with 3 images
- 2. A certain zener diode has a maximum power rating of 300 mW at 40 deg Cand a derating factor of 1.4mW/deg C. Determine the maximum power the zener can dissipate at a temperature of 80 deg C. 3. From the datasheet, a 1N4728A zener diode has a ZZ of 10 0. The datasheet gives VZ = 3.3 V at a test current, IZ, of 76 mA. What is the voltage across the zener terminals when the current is 90 mA? When the current is 45 mA?The step up chopper has R=20 ohm and out put voltage is 120V. The source voltage is 40V DC . The load inductance is 0.2mH. If the chopper frequency is 4KHZ find1- the duty cycle2- the average value of source current3- TON4- Imax5- Imin6-The average value of diode currentFor self bias configuration. Solve for Ib and Ic. ... 4 RC 15002 RB VCC 5 16V 100A/A 80 kQ Re 10002 Ib=Blank 1 HA Ic=Blank 2mA
- Number 9 Please show your detailed solution. Number 9 Please show you detailed solution. A 50-ohm resistor is in series with a 40-?F capacitor across a constant potential source of 180 volts. Determine frequency that will give current of 3.13 amp. A. 250 Hz C. 160 Hz B. 200 Hz D. 140 HzA three-phase rectifier is supplied by a 173.2-V rms line-to-line 60-Hz source. The RL load is a 100 resistor in series with a 15-mH inductor. Determine THD taking Is1 = 1.35400 V is the input voltage given to a chopper, the required output is 650 V. The thyristor is conducting 300 usec. what is the addition of conducting and non conducting period? (Write your answer in usec) Answer:
- Rs e = 10 Vrms MA Rsh=S00n Rmz500.2 %3D Each diod has an average forwerd resistance of 50e and is assumedto have an inf inite resistance in the reerse direction Calculate 1-Rs 2-The a.c. Seasitivity 3- the sensitivity. d.c. equivra fant wwwIn a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.55 V respectively. The form factor of this circuit is a. 3.67 b. 0.55 c. 1.35 d. 1.83Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
- quations. 3. What are the advantages and disadvantages of a dual slope ADC? a blecL mationXc 10 ? 100 2 R 20 2 E = 120 V ZThe D diode used in the diode circuit shown in the figure is a silicon diode. a. Plot the output voltage of the circuit. b. Describe the working principle for each phase in detail R1 10 kN V out +12 V D R2 100 N Vin-15 sin(wt) R3 220 N