The 1800-kg boat is suspended from two parallel cables of equal length. The location of the center of gravity of the boat is not known. Calculate the force P required to hold the boat in the position shown.

Q: 2040 180 720 1080 0 Dimensions in millimeters The three feller cuts off large trees near ground…

A:

Q: The 43-kg homogenecus smooth sphere rests on the 36° incline A and bears against the smooth vertical…

A:

Q: Weight of the body 30 kg Find the value of the force P that keeps the body in equilibrium on a…

A:

Q: The plate has a mass of 25 kg has its center of gravity at G. It is supported in the horizontal…

A: Given Datam=25kgW=25×9.81=245.25N Here we are taking the moments according to the axes x,y, as given…

Q: The weights of the various components of the truck are below. Replace this system of forces by an…

A: To find: The equivalent resultant force and also specify the location measured from A. Given: The…

Q: Determine the maximum weight of the oil barrel that the floor crane can support without falling and…

A:

Q: The 46-kg homogeneous smooth sphere rests on the 32° incline A and bears against the smooth vertical…

A: When an amount of push or the pull applied on the object, it has the ability to change its state…

Q: The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown…

A:

Q: 2/111 The weight of the computer system is 80 lb with center of gravity at point G. Determine the…

A:

Q: Determine the components of the 300-lb force directed down to the right at a slope of 2 (opposite)…

A: Given data: F=300 lb Need to determine the components of the force.

Q: It is desired that a person be able to begin closing the van hatch from the open position shown with…

A:

Q: The shear leg derrick is used to haul the 162-kg net of fish onto the dock. Determine the…

A:

Q: Determine the x and y scalar components of F= 250 lb

A: Draw the schematic diagram for the above problem.

Q: the indicated location of the center of gravity of the 3100-lb pick truck is for the unlanden…

A:

Q: The signboard truss is designed to support a horizontal wind load of 610 lb. If the resultant of…

A: Draw the free-body diagram of the above section of truss by taking section AG.

Q: Determine the force that a man of weight W must exert on the rope to support himself. Determine the…

A: Given DataT-Tesions of the stringW= Weight of the Body

Q: Calculate the magnitude of the force acting on the pin at D. Pin C is fixed in DE and bears against…

A:

Q: Calculate the forces acting at pin A, pin B, and pin C. 6 m 5 kN 1.5 m y 1.5 m x OB 3 m 3 m

A: Calculate the forces acting at pin A, pin B, and pin C.

Q: Determine the absolute weight and the weight rela- tive to the rotating earth of a 60-kg woman if…

A:

Q: A truck is driving over a scale at a weight station. When the front wheels drive over the scale, the…

A:

Q: 3. The unstretched length of an elastic cord is made to run vertically from the ceiling down to the…

A: Given data: The slope of an inclined cord, s = 4/5. Let T be the tension in the cord and F is a…

Q: The crane's arm has a pin support at A, and the hydraulic cylinder BC exerts an axial force on the…

A:

Q: Find the center of mass of the system shown if M1= 10 kg, and M2= 20 kg.

A:

Q: In a hydraulic press, the small cylinder has a diamter of 1 in, while the large piston has a…

A: To Find : The force on the large piston. Given :  The diameter of larger piston is d=8 in. The…

Q: Determine the forces acting on the frame. Draw the free-body diagram of each of the members showing…

A:

Q: Determine the forces at the contact surfaces A, B and C. Assume frictionless surfaces for all points…

A:

Q: The y-component of the force F which a person exerts on the handle of the box wrench is known to be…

A:

Q: The 53-kg homogeneous smooth sphere rests on the 40° incline A and bears against the smooth vertical…

A:

Q: The crane truck has a weight of 14250 lb and a center of gravity at point CG. The parking brake only…

A: To finddetermine the maximum force F applied at the angle  that can be exerted on the crane without…

Q: The block shown in the figure below is acted on by its weight, W = 1300 Lbs, a horizontal force H =…

A:

Q: The signboard truss is designed to support a horizontal wind load of 770 lb. If the resultant of…

A:

Q: crane consists of three parts, which have weights of W₁-3700 lb, W₂-750 Vs-1600 lb and centers of…

A: W=720lb W1=3700lb W2=750lb W3=1600lb To find reaction on front and rear wheel

Q: The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown…

A: Given Data The angle of the crane is: θ=32° The distance a is:a=7 in The distance b is: b=34 in The…

Q: B – 2.4 m -1.5m-l 0,6m 2m Im

A: Draw free body diagram of truck,

Q: The machine shown is used for moving heavy items such as pallets of bricks around construction…

A:

Q: 4. A vertical force F is applied to the cord that wraps over a pipe with a cylinder support by the…

A: Consider the mass of the cylinder as m. Draw the free-body diagram of the cylinder.

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: Step 1: Step 2: Step 3: Step 4:

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.