The 113-lb force P is applied to the 230-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μ = 0.48, μ = 0.38.

The 113-lb force P is applied to the 230-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μ = 0.48, μ = 0.38.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 10 kg block rest on an inclined plane mak ing an angle of 30° wi th the horizontal. a. Find the coefficie nt of friction betwee n the block and the p lane to keep the bloc k from sliding. b. Determine the norm al reaction. c. Determine friction al force.
1-21_Problems Q:1/ A hollow right-circular cylinder is made of cast iron and has an outside diameter of (75 mm) and an inside diameter of (60 mm). If the cylinder is loaded by an axial compressive force of (50 kN), determine the total shortening in a (600 mm) length. Also determine the normal stress under this load. Take the modulus of elasticity to be (100 GPa). Ans.(ô = 0.188 mm) , (o= 31.45 MPa) Q:2/A square steel bar is (50 mm) on a side and (250 mm) long. It is loaded by an axial tensile force of (200 kN). If(E= 200 GPa) and (µ= 0.3), determine the change of volume per unit volume. (Ans. 0.00016) Q:3/The bar shown in Fig.(1-22 ) is subjected to a tensile load of (160kN). If the stress in the middle portion is limited to (150N/mm³), determine the diameter of middle portion. Find also the length of the middle portion if the total elongation of the bar is to be (0.2mm). Young's modulus is given as equal to (2.1*10$ N/mm³). (Ans. d= 3.68em , L=20.71em) 160 KN A 6 cm DIA 160 N 6 om DIA…
Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate ftop at the ends. (MPa), consider sign convention (- for compression, + for tension) Š KN/m EXCLUD In6 SELFWEI6HT 300 = P P = 300 kN 15M オ 400 Ye = 24 1N m3 N.A. 800 70
Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate ftop at the ends. (MPa), consider sign convention (- for compression, + for tension) Skw/m EXCLUD in6 SELFWEI6HT 300 =P P=300 kN ISM オ 400 片 de = 24 IN m3 N.A. 800 70
Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate fbot at the ends. (MPa), consider sign convention (- for compression, + for tension) SELEWEILHT 300 P P 300 kN 400 de= 24 m3 900 70
A compound shaft made of steel and aluminium transmits 75 kW at 900 rpm. Determine the maximum shear stress and relative angle of twist between surfaces at two extreme ends located at A and C. Neglect any strain concentration effect. Esteel = 207 GPa, EA1 = 73 GPa, VAI = 0.334, and Vsteel = 0.33. F Aluminium 60 800- B Steel 75 1000 All dimensions are in mm
momentum.pdf 9/1 The se extra examples are presented by Mohammed Dheyaa 2021© H.W.l Giuen V, = 25m/s S.g.= 0.83 Find the force requited F-マ。 plate d=somm v, = 36m/s negkcting frichion betu
(40 H.wA Rismatic steel bar of a Square cro ss section (lookloo)mm is locoled by compressive forcc P= 1300 k, the bar has length 2.5 m, =200 G Pa, V=0.3, determine the Shortening S, the Incrense in the dimensions of cross Section, the change In Volume DV of the bar? 7. loomm loomm
Question 1 The same torque is applied to two tubes with identical metal sheets, determine the ratio of T circle/Tsquare of the shear stresses. Given: r= 14 mm, S = 19 mm, and t = 2.84 mm. 43 FETOO KA F1 F2 FS FB F7 F8 ESC T H.
7. The 50-mm diameter rubber rod is placed in a hole with rigid lubricated walls. There is no clearance between the rod and the sides of the hole. Determine the change in the length of the rod when 8-KN load is applied. Use E = 40 MPa and v = 0.45 for rubber. 8 kN 50mm X 300mm
Title: Design of Beam in Flexure (WSD Method) PROBLEM: Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar diameter = 20 mm. Take b = d/2. Use WSD method. As (Gomm 20 KN lo Ka/m 8 KN/m 3m
The lawn roller has a mass of 80 kg. If the arm BA is held at an angle of 30° from the horizontal and the coefficient of rolling resistance for the roller is 25 mm, determine the force P needed to push the roller at constant speed. Neglect friction developed at the axle, A, and assume that the resultant force P acting on the handle is applied along arm BA. .P 250 mm A 30° IMPORTANT: 1. Solution for PS2 is not required to be submitted. 2. Round the final answer to three decimał places. 3. To match the key answers, you have to round only the final answer. Do not round in between your solutions. Answer: P =