The 100V source is absorbing 50w of power in the network shown in the Figurewhat is the value of R and what power delivered or absorbed by the currentsource of 5AR=...... , PsA=.....wa- 27.71 , 725 , deliveringb- 17.27 , 275absorbingc- 17.27 , 275 deliveringd- 71.72, 572 absorbinge- 71.72 , 572 deliveringf- 27.71 , 725 absorbing5 Avs(1)A 001 A0

Answered: Image /qna-images/answer/0734516d-77ef-4652-9c8c-ab98df15430c.jpg

Answered: The 100V source is absorbing 50w of…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

The 100V source is absorbing 50w of power in the network shown in the Figure what is the value of R and what power delivered or absorbed by the current source of 5A R-..n, PSA=..w a- 27.71, 725, delivering b- 17.27, 275absorbing c- 17.27, 275 delivering d- 71.72, 572 absorbing e- 71.72, 572 delivering f- 27.71, 725 absorbing 102 102 R. 200 V 100 V Answer:
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
Calculate the rms values of load voltage and current for the circuit shown below. Please show work
AC Circuits Current, Voltage, Power, Power Factor and Phasor Diagrams. Consider the circuit shown in Figure 3. (i) Find the total impedance ZT as seen by the voltage source. (ii) Find the total current IT supplied by the source. (iii) Sketch phasor diagram of Vs and IT and State whether IT leads or lags Vs (iv) Determine the power factor angle for the circuit. 9. L R1 1002 0.213H IT Vs R3 1502 C 12020°V 22µF 60HZ R2 50Ω Figure 3 Answers |(1) Zr = (ii) IT= (iii)
A 60Hz sourcewith an effective voltage of 240 volts supplies 4500 volt-amp to a load with a p.f. of 0.75 lagging. Determine the parallel capacitance required to improve the power factor to: a) 0.9 lagging and b) 0.9 leading. What per cent reduction in line current resulted in part (a)?
Discuss Fully the various methods available for transforming 3-phase voltages to higher or lower 3-phase voltages. Highlight the advantages and disadvantages of each. Include the connection diagrams.
A 2000 KVA, 6600/400V , STAR/Delta was performed with short circuit and Open circuit test with the following results: O.C. Test : 400V, 150A and 15kw S.C. Test: 400V, 175A and 17kw Determine the percent impedance drop for resistance, reactance and impedance. Also calculate for the efficiency at half load, 0.80pf lagging and full load, 0.85pf leading.
Using PV Curve explain the effects of more real power, increasing excitation and how this helps maintain frequency. Describe the interlink between load angle and power.
What is load curve
Calculate the impedance ?? for the maximum average power transfer in the circuit shown in Figure 3.and ??Find the value of the maximum average power transferred to?
OR e) What is BILS? Explain their significance in power system studies.
You want to feed a load that works at 100Vrms and consumes 2KVA with a lagging power factor of 0.8. To supply the load, a transformer is required whose equivalent circuit is shown in figure b) and two sections of transmission lines shown in figure c). The general feeding scheme is shown in figure a). Without using the mesh or node methods, determine the power triangle of the power supply.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning