Technician A says hypoid gearset are only used in RWD vehicle drivetrains. Technician B says hypoid gearset multiply torque. Which technician is correct? A- Technician A B- Technician B C- Both A and B D- Neither A nor B.

Q: While diagnosing a complaint of excessive play in the steering on a vehicle with power steering:…

A: The correct option is b.

Q: What is the purpose of of the viscous clutch?a. to engage engine otrque to the transmission.b. to…

A: The correct option is: b. to improve mobility when driving conditions become difficult Explanation:…

Q: Words: Axles, Differential, Gear, Housing, Propelled, Ring, Side, Transaxle, Transfers,…

A: Since Yoo have posted question with multirple subpart in a single request we will solve first three…

Q: What is used in a typical 4WD pickup truck to prevent driveline windup during turns?a. Constant…

A: Constant velocity joints in the driveshafts of a typical 4WD pickup truck are used to allow for…

Q: Technician A says that some small cracks in the accessory drive belt may be within tolerance.…

A: Technician A says that some small crack in the accessory drive belt may be within tolerance limits.…

Q: Technician A says when removing a transmission, the rear of the engine will usually need to be…

A: Answer

Q: When discussing the possible causes for a shudder during acceleration, Technician A says that a worn…

A: Shudder is taken place during acceleration at higher speed. The main reason of this problem is…

Q: Tech A says that camber changes as the suspension moves up and down.  Tech B says that camber…

A: Camber angle : The angle made by the vertical axis with the wheel is known as camber angle . It is…

Q: Among the following, which drive transmits exact velocity ratio during power transmission. Gear…

A: Gear drive

Q: Technician A says that some systems use a special modulated shift control solenoid. Technician B…

A: In automobile the transmission system uses shift control solenoid which shift the gear…

Q: Tech A says that negative caster provides directional stability.  Tech B says that positive caster…

A: The caster can be defined as the angle of inclination of the steering axis from the vertical axis of…

Q: Which of the following components is replaced as an assembly?a. The transfer caseb. the viscous…

A: Step 1:The transfer case is often replaced as an assembly due to several reasons :Transfer cases are…

Q: What results from having different axle ratios on thefront and rear of a 4WD vehicle when it is…

A: Given Data : 4WD Axle ratio

Q: what will happen as the clutch disc wears? a. transmission shifting becomes easier b. clutch pedal…

A: The correct option is: c. clutch pedal free play increases. As the clutch disc wears, the friction…

Q: in an automatic transmission or transaxle, the torque converter is used to

A: The Torque Converter A torque converter is a device that is used to transmit the rotating power of…

Q: Explain the primary operational difference between a full time and a part time four wheel drive…

A: Introduction A four-wheel drive vehicle, often known as a 4WD or four-by-four, is one that receives…

Q: What determines whether a conventional transmission or a transaxle is used?

A: Manual transmissions feature a foot-operated clutch pedal and a shifter that allows the driver to…

Q: The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the…

A: The function of engine mounts is to limit the movement of the engine, hold it in a position and…

Q: 2. Technician A says that the purpose of the steering wheel holder is to make sure that the steering…

A: In this problem, Technician A is talking about the purpose of a steering wheel holder. He is telling…

Q: What is the maximum torque? to avoid damage from throttle r LAB T

A:

Q: When the input and output shafts are turning at the same speed, the transmission is in ____ drive.

A: To explain: When the input and output shafts are turning at the same speed, the transmission is in…

Q: What can too much clutch pedal free play cause? a.hard gear shifting b.fast release bearing wear…

A: The correct option is d. clutch slipping. Excessive clutch pedal free play can cause the clutch to…

Q: Pinion gear-to-flywheel ring gear clearance is beingdiscussed: Technician A says that if there is…

A: Given  Pinion gear-to-flywheel ring gear To find Which technician is correct

Q: Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the…

A: Automobile

Q: Design and model of a basic mobile platform (2 wheel drive)

A:

Q: In an ideal Otto cycle, the initial pressure and temperature of air are 100 kPa and 18 degree C.…

A: GIVEN DATA FOR OTTO CYCLE COMPRESSION RATIO r=8 P1= 100KPa T1= 18'C T3=600'C WE HAVE TO FIND MAXIMUM…

Q: What is the correct sequence for adjusting alignmentangles during a four-wheel alignment?

A: Given Data : Adjusting alignment angles during four wheel alignment.

Q: List three possible causes of a noisy bearing during clutch operation.

A: There are many types of clutch noises such as whistling or whining, rattling noises, and many more.…

Q: Differential system uses worm and wheel gears O helical gears. O spur gears. gears with moving axes.…

A:

Q: Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have…

A: Given Transaxle problem To find Statement with is/are correct Shifting problem of transaxle can be…

Q: . Technician A says that leaf spring-type rear sus- pensions are subject to axle tramp. Technician B…

A: We are authorized to answer one question at a time since you have mentioned question 4 only so we…

Q: 108) Technician A says that engine management malfunctions may be misinterpreted as transmission…

A: Engine management malfunctions can be seen by malfunction indicator lamp . this indicator shows that…

Q: the number one cause of clutch disc failure

A: Clutch :- The function of a clutch is to transmit the power from rotating shaft or motor or engine…

Q: 69) Technician A says a multiple-disc holding clutch is used to lock the input and output shafts…

A: Introduction :Multiple disk clutches are used to deliver extremely high torque in minimal…

Q: In a typical all wheel drive automatic transaxle, what controls the transfer clutch?a. Transmission…

A: In a typical all-wheel-drive automatic transaxle, the transfer clutch isn't directly controlled by a…

Q: Technician A says that a hunting gearset is one inwhich one drive pinion gear tooth contacts only…

A:

Q: what is the first alignment angle to be adjusted when performing a front wheel alignment? A. CAMBER…

A: To determine: The first alignment angle to be adjusted when performing a front wheel alignment…

Q: Which of the following gear ratios indicates an overdrivecondition?a. 2.15 : 1b. 1 : 1c. 0.85 : 1d.…

A: According to the details provided in the question, we need to calculate GEAR RATIO for the…

Q: A clicking noise during transmission/transaxle operationmay be an indication of __ .a. worn…

A: Given Data : Clicking Noise  Transmission operation

Q: A discussion concerning CV joint testing is being held. Technician A says that a recommended method…

A: CV Joint:  CV joint means Constant Velocity Joint. They are used to transfer the power in a variable…

Q: 76) How is clutch pack clearance adjusted? O Selective rate piston springs O Selective sized snap…

A: How is clutch pack clearance adjusted? Selective rate piston springs Selective sized snap rings…

Q: 128) Technician A says slide hammer pullers are usually required to remove the front pump from the…

A: A slide hammer puller is a mechanical tool with a long round shaft. It has a hammer weight slides. A…

Q: 78) Technician A says when a driving clutch is released, the drive discs drive the driven discs…

A: Given Clutch assembly To find How the assembly works

Q: The four common configurations used as the finaldrives on FWD vehicles are the __ gear, __ gear,__…

A: The four often utilized final drive designs for FWD cars are chain drive, hypoid gear, planetary…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.